Frag Glues and Epoxy

25 products

Availability

  • Buy Aquascape Milliput Epoxy at www.jlaquatics.com Aquascape Milliput Epoxy

    Aquascape Milliput Epoxy

    1 review

    In Stock

    Aquascape Milliput Epoxy (Coralline Purple) Overview D-D Aquascape is a two-part epoxy putty developed with Milliput for underwater use in marine and freshwater aquariums. The coralline version cures underwater to a purple tone that blends with reef rock while providing a strong, reef-safe bond for rockwork and corals. Features Underwater-curing two-part epoxy for aquascaping and repairs Stickier formulation to grip wet rock and frag plugs Cures to coralline-algae purple for discreet joints Saltwater and freshwater compatible Machineable and heat-resistant once fully cured Specifications Pack size: 113 g (4 oz) two sticks (resin & hardener) Working/curing: semi-hard in ~3–4 hours at 20–25 °C; full cure overnight Heat resistance: up to ~130 °C when cured Colours available: Coralline (ASMP002) and Slate Grey (ASMP003); this listing is Coralline How to Use Knead equal parts until uniform; apply to clean rock, frag base, or equipment For reactors/returns or large corals, support pieces until set Avoid over-manipulating in a stocked tank; excessive working can cause harmless talc haze—pause and aerate if water clouds

    In Stock

    $12.65

  • Buy Seachem Reef Glue (20 Gram) at www.jlaquatics.com Seachem Reef Glue (20 Gram)

    Seachem Reef Glue (20 Gram)

    1 review

    In Stock

    Seachem Reef Glue is a superior cyanoacrylate gel for gluing and mounting coral frags and colonies to reef rock or plugs. It bonds within seconds and has excellent control, hold and durability characteristics. It can even be used underwater.Reef Glue can be used for any aquascaping in freshwater or saltwater aquariums or for any plastics repairs.Reef Glue comes in an aluminum tube for extended stability beyond products contained in plastic bottles - it won't dry up in the tube.With a new formula that is 17x thicker, there's more control while gluing and less mess in application!Directions Dispense a small amount of glue prior to each use. Apply a small amount of Reef Glue to one of the surfaces and press parts together for 20 seconds. Wipe tip free of glue before replacing the cap.WARNINGCyanoacrylate. Danger. Bonds skin and eyes in seconds. Keep out of the reach of children. Eye and skin irritant. If eye contact occurs, rinse with water for 5-10 minutes.

    In Stock

    $11.15

  • Buy Oceans Wonders Reef Glue Gel (2oz) at www.jlaquatics.com Oceans Wonders Reef Glue Gel (2oz)

    Oceans Wonders Reef Glue Gel (2oz)

    1 review

    In Stock

    Oceans Wonders Reef Glue Gel (2oz) OverviewDouble-size reef adhesive gel for extended fragging sessions; delivers strong underwater bonding and controlled application.Features 2 oz gel tube Rapid underwater cure Reef-safe formulation Precision nozzle Extended usage capacity Specifications Volume: 2 oz (56 g) Formula: Cyanoacrylate gel Packaging: Plastic tube Color: Translucent UPC: 804879061809

    In Stock

    $19.95

  • Buy Oceans Wonders Reef Glue Gel (1oz) at www.jlaquatics.com Oceans Wonders Reef Glue Gel (1oz)

    Oceans Wonders Reef Glue Gel (1oz)

    In Stock

    Oceans Wonders Reef Glue Gel (1oz) OverviewPremium reef-safe gel adhesive formulated for rapid coral fragment bonding and minimal mess; suitable for LPS, SPS, and soft corals.Features 1 oz gel squeezable tube Fast-curing underwater formula Non-toxic, reef-safe ingredients Precision applicator tip Low-odor, easy cleanup Specifications Volume: 1 oz (28 g) Formula: Cyanoacrylate gel Packaging: Plastic tube with cap Color: Translucent UPC: 804879061786

    In Stock

    $12.70

  • BSI Insta-Set Accelerator Pump Spray 2 oz. BSI Insta-Set Accelerator Pump Spray 2 oz.

    BSI Insta-Set Accelerator Pump Spray 2 oz.

    In Stock

    BSI Insta-Set Accelerator Pump Spray 2 oz. Overview INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joint's strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam. Directions After joining parts with cyanoacrylate (CA, super glue), spray the seams with Insta-Set to cure the CA in 8 seconds. A bead of CA can then be applied to the outside and corners of joints before another application of Insta-Set to reinforce their strength. Insta-Set can also be applied to one part (with CA on the other) before joining for difficult to bond materials. Insta-Set is compatible with all surfaces, including clear plastic and all foams. It also is a great cleaning agent for adhesive residue and scuff marks. Store separately from CAs.

    In Stock

    $9.95

  • BSI IC-Gel Insta Cure Gel 20g Aluminum Tube BSI IC-Gel Insta Cure Gel 20g Aluminum Tube

    BSI IC-Gel Insta Cure Gel 20g Aluminum Tube

    In Stock

    BSI IC-Gel Insta Cure Gel 20g Aluminum Tube Overview IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE. IC-GEL, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want. IC-GEL is an excellent putty for plastic models. It will fill any void and can be formed to many shapes. Applying INSTA-SET allows IC-GEL to be sanded or filed to final shape in less than 20 seconds. Autobody repairmen have finished their jobs in a fraction of the time by using IC-GEL with the additional advantage over normal body putties of superior bonding to metal surfaces. IC-GEL's most popular application is for the bonding of fragments of live coral (frags) to underwater rocks in aquariums. It has proven to be non-toxic to aquatic organisms and provides instant bonding for the propagation of the coral. IC-Gel has a superior shelf life of over three years and its application nozzle makes it the easiest of all CAs to apply. Directions Screw on top and cap unit to puncture seal on the tube. Remove cap and apply IC-GEL to one surface, and then hold parts tightly together. Sets in 10-25 seconds. Replace cap immediately after use. Store in cool dry place.

    In Stock

    $11.95

  • Buy PolypLab Premium Frag Glue (28 Gram) at www.jlaquatics.com PolypLab Premium Frag Glue (28 Gram)

    PolypLab Premium Frag Glue (28 Gram)

    2 reviews

    In Stock

    PolypLab Premium Frag Glue (28 Gram) Overview Premium Frag Glue is an ultra-thick super glue gel designed for coral fragging and aquascaping. Its extended open time lets you position frags precisely while it reacts and bonds in water within seconds. Safe for saltwater and freshwater use when applied as directed. Why it’s different Ultra-thick gel holds shape for gap filling and large frags Works underwater and bonds in about 5–15 seconds once submerged Up to ~8 hours working time in air for extended frag sessions Positive-pressure aluminum tubes minimize waste and back-siphon Each tube has its own uniform-diameter application stem; child-proof ring on first use Specifications Type Ultra-thick super glue gel Bond time in water ~5–15 seconds Open/working time in air Up to ~8 hours Water types Saltwater or freshwater Packaging Seven 4 g aluminum tubes (total 28 g) Directions Clean the mounting surface. Apply a small bead to the frag or rock. Press and hold underwater for 5–15 seconds until initial grab forms. For heavy pieces use two small beads rather than one large blob. Replace cap promptly between frags to preserve working time. What’s Included Seven (7) single-use tubes × 4 g each (28 g total) Application stems integrated with each tube

    In Stock

    $21.25

  • Buy Seachem CoralCrete - 4oz Purple at www.jlaquatics.com

    Seachem CoralCrete - 4oz Purple

    In Stock

    Seachem CoralCrete is two-part epoxy putty that can be used to secure coral to rock work or to fuse together rock work for more stable foundations in reef aquaria. It has a working time of 5 minutes which allows for plenty of work time while also quickly securing coral or rock.CoralCrete is ideal for working with larger colonies of branching coral, most large polyp coral or adhering plating coral to rock work.CoralCrete is safe for aquarium inhabitants when used as directed.Features Epoxy adhesive for securing coral to rock work Fully cures submerged or emerged within 24 hours Matches synthetic reef rock Marine and freshwater safe DirectionsFor sensitive skin, wear latex gloves. Cut off desired amount of CoralCrete. Replace unused CoralCrete into plastic storage tube. Remove film and knead CoralCrete together until uniform color is achieved. Once mixed, CoralCrete can be used to adhere coral or rock, either submerged or emerged. Press firmly around base or contact point of coral or rock to insure CoralCrete penetrates pores and surface grooves.Curing begins in about 5 minutes, hardening in about 15 minutes. CoralCrete cures fully in 24 hours. Protein Skimmers may over activate during cure time.

    In Stock

    $13.00

  • Ecotech Marine Frag Glues and Epoxy Ecotech Elements Coral Glue (75ml)

    Ecotech Elements Coral Glue - 75ml

    In Stock

    Ecotech Elements Coral Glue - 75ml Overview Whether you're working with coral frags or sculpturing your live rock; this glue will get the job done. Finally superior inter-molecular bonding in a form that is easy to apply, less messy, and has an extended shelf life. Try a superior product from the company that brought you the VorTech pump and experience glue the way it should be. Features Glue your corals upside down in your tank Glue your corals and rock under water Sets in 10 seconds Cures in 5 minutes Triple distilled for purity pH neutral Gel Consistency Non-clogging pin-cap 2 year shelf life

    In Stock

    $47.99

  • Buy PolypLab Premium Frag Glue (25 x 4 Gram) at www.jlaquatics.com PolypLab Premium Frag Glue (25 x 4 Gram)

    PolypLab Premium Frag Glue (25 x 4 Gram)

    In Stock

    PolypLab Premium Frag Glue (25 x 4 Gram) Overview The Grenade Pack delivers 25 single-use tubes of Polyplab’s ultra-thick frag glue for busy frag racks and club workshops. The gel’s body lets you set and stick even in high-flow areas and it reacts in water fast for reliable bonds on plugs rubble or live rock. Benefits Ultra-thick gel you can make ice-cream cones with for precise placement Bonds underwater in ~5–15 seconds for fast mounting Long open time (~8 hours in air) supports extended fragging sessions Positive-pressure aluminum tubes prevent back-siphon and reduce waste Uniform application stems on every tube; child-proof ring on first use Specifications Type Ultra-thick super glue gel Bond time in water ~5–15 seconds Open/working time in air Up to ~8 hours Water types Saltwater or freshwater Packaging 25 aluminum tubes × 4 g each Directions Apply a small amount to the frag base or rock. Submerge and press firmly for 5–15 seconds until the initial bond forms. For large frags or uneven rock use multiple small beads. Cap between uses to maintain viscosity and shelf life. What’s Included Twenty-five (25) single-use tubes × 4 g Grenade Pack Application stems integrated with each tube

    In Stock

    $56.75

  • Buy D-D Coral Viewing Glasses at www.jlaquatics.com D-D Coral Viewing Glasses

    D-D Coral Viewing Glasses

    In Stock

    D-D Coral Viewing Glasses Overview See true coral colours under blue-heavy reef lighting. These orange-tinted glasses filter actinic blue light so fish and corals appear in a more natural balance while glare is reduced and detail pops during inspection, photography, or frag placement. Features Orange lenses filter excess actinic/blue for natural colour rendering UVA protection with reduced reflected and scattered light Comfortable everyday fit for quick tank checks and photo sessions Useful beyond the tank to cut screen and surface glare Specifications Lens tint: orange Protection: UVA Use case: view tanks lit by blue/actinic LEDs or T5s UPC/EAN: 5060444553420

    In Stock

    $12.95

  • BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 2oz

    BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 2oz

    In Stock

    BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 2oz Overview Maxi-Cure extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE is usually the least expensive option for this application. Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220F. Soak extender tip in acetone for cleaning.

    In Stock

    $17.25

  • Buy Reef Crest Aqua Weld (150 Gram) at www.jlaquatics.com Reef Crest Aqua Weld (150 Gram)

    Reef Crest Aqua Weld (150 Gram)

    In Stock

    Reef Crest Aqua WELD is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then use it to fuse dry rockscapes, repair broken plastic components, and virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape. 250ml Container contains 150 Grams (net weight) of Aqua WELD.

    In Stock

    $13.95

  • Buy Reef Crest Aqua Weld Pro (150 Gram) at www.jlaquatics.com Reef Crest Aqua Weld Pro (150 Gram)

    Reef Crest Aqua Weld Pro (150 Gram)

    1 review

    In Stock

    Reef Crest Aqua WELD PRO is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius. Aqua WELD PRO contains specially treated purple beads that when mixed with the clear ones more closely simulates coralline algae and thus blends into your established aquarium better.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then fuse rockscapes, repair plastic parts, or virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Purple color blends into established aquariums. Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape. 250ml Container contains 150 Grams (net weight) of Aqua WELD.

    In Stock

    $16.95

  • Buy Ecotech Elements Coral Glue (295ml) at www.jlaquatics.com Ecotech Elements Coral Glue (295ml)

    Ecotech Elements Coral Glue - 295ml

    In Stock

    Ecotech Elements Coral Glue - 295ml Overview Whether you're working with coral frags or sculpturing your live rock; this glue will get the job done. Finally superior inter-molecular bonding in a form that is easy to apply, less messy, and has an extended shelf life. Try a superior product from the company that brought you the VorTech pump and experience glue the way it should be. Features Glue your corals upside down in your tank Glue your corals and rock under water Sets in 10 seconds Cures in 5 minutes Triple distilled for purity pH neutral Gel Consistency Non-clogging pin-cap 2 year shelf life

    In Stock

    $119.99

  • Reef Crest Aqua Weld Pro (300 Gram) Reef Crest Aqua Weld Pro (300 Gram)

    Reef Crest Aqua Weld Pro (300 Gram)

    In Stock

    Reef Crest Aqua WELD PRO is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius. Aqua WELD PRO contains specially treated purple beads that when mixed with the clear ones more closely simulates coralline algae and thus blends into your established aquarium better.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then fuse rockscapes, repair plastic parts, or virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Purple color blends into established aquariums. Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape. 250ml Container contains 150 Grams (net weight) of Aqua WELD.

    In Stock

    $28.75

  • BSI INSTA-CURE+ Gap Filling Glue 1oz

    BSI INSTA-CURE+ Gap Filling Glue 1oz

    In Stock

    BSI INSTA-CURE+ Gap Filling Glue 1oz Overview Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220 F. Soak extender tip in acetone for cleaning.

    In Stock

    $10.95

  • BSI Slow Cure Epoxy - 30min - 4.5oz BSI Slow Cure Epoxy - 30min - 4.5oz and 9oz sizes in packaging.

    BSI Slow Cure Epoxy - 30min - 4.5oz

    In Stock

      BSI Slow Cure Epoxy - 30min - 4.5oz

    In Stock

    $21.95

  • Reef Crest Aqua Weld (300 Gram) Reef Crest Aqua Weld (300 Gram)

    Reef Crest Aqua Weld (300 Gram)

    1 review

    In Stock

    Reef Crest Aqua WELD is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then use it to fuse dry rockscapes, repair broken plastic components, and virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape. 500ml Container contains 300 Grams (net weight) of Aqua WELD.

    In Stock

    $24.60

  • Buy Reef Crest Aqua Weld Pro (600 Gram) at www.jlaquatics.com Reef Crest Aqua Weld Pro (600 Gram)

    Reef Crest Aqua Weld Pro (600 Gram)

    3 reviews

    In Stock

    Reef Crest Aqua WELD PRO is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius. Aqua WELD PRO contains specially treated purple beads that when mixed with the clear ones more closely simulates coralline algae and thus blends into your established aquarium better.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then fuse rockscapes, repair plastic parts, or virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Purple color blends into established aquariums. Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape. 250ml Container contains 150 Grams (net weight) of Aqua WELD.

    In Stock

    $46.95

  • Buy Reef Crest Aqua Weld (600 Gram) at www.jlaquatics.com Reef Crest Aqua Weld (600 Gram)

    Reef Crest Aqua Weld (600 Gram)

    Reef Crest Aqua WELD is a unique thermoplastic polymer made up of small plastic beads which melt at around 60 degrees Celsius.By heating these beads in hot water the aquarist can easily melt the pellets to form a transparent flexible material. Once melted the opaque white pellets fuse together, become transparent and soften. You can then use it to fuse dry rockscapes, repair broken plastic components, and virtually anything else you want together for a lasting and very strong bond. Features: Re-usable as many times as required Great for aquascaping and general DIY work. 100% non-toxic Very strong once hard Easy to mold by hand - no sticky residue Cures in minutes underwater Safe for both freshwater and saltwater aquariums. Directions: Determine how much Aqua WELD you will require to perform the task (when using Aqua WELD, keep in mind that it is similar to using two-part epoxy, but without the mess, and tank clouding).Heat some water in a microwave to approx. 60 C (approx. 1-2min in a 1200W microwave), or to just below boiling, and pour in the pellets. Allow the pellets to become transparent (usually takes 10-15 seconds)Remove from the water with a utensil (a fork works best) and mold the Aqua WELD around the pieces you want to fuse together. As the mixture cools it will harden in place, but you can reheat it in order to reshape.1000ml Container contains 600 Grams (net weight) of Aqua WELD.

    $36.95

  • BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 8oz

    BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 8oz

    In Stock

    BSI Maxi-Cure Extra Thick Cyanoacrylate Glue - 8oz Overview Maxi-Cure extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE is usually the least expensive option for this application. Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220F. Soak extender tip in acetone for cleaning.

    In Stock

    $48.95

  • BSI Replacement Cap for 2 oz Glue Bottles

    BSI Replacement Cap for 2 oz Glue Bottles

    In Stock

    BSI Replacement Cap for 2 oz Glue Bottles Overview Replacement combination of top and screw-on cap that has a built-in pin for Pocket CAs. Will fit on BSI Pocket CA bottles only. Can also be used on Oceans Wonders 1 and 2oz glue bottles.

    In Stock

    $1.45

  • BSI Quick Cure Epoxy - 9 oz

    BSI Quick Cure Epoxy - 9 oz

    In Stock

    BSI Quick Cure Epoxy - 9 oz

    In Stock

    $34.95

  • BSI Glue Extender Tips - 6 Pack

    BSI Glue Extender Tips - 6 Pack

    In Stock

    BSI Glue Extender Tips - 6 Pack Overview For use with BSI's Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas. Will also work the Oceans Wonders 1 and 2oz Glue Bottles.

    In Stock

    $4.45

Login

Forgot your password?

Don't have an account yet?
Create account