Hydros Flow Sensor - 1 Inch
Overview
The HYDROS Flow Sensors are easy-to-install and measure the flow rate of water passing through it using the HYDROS app.
Available in four sizes: 3/4in (40-800gph), 1in (50-1500gph), 1.5in (100-2500gph), 2in (9200-4050gph)
Monitor Water Flow with
The HYDROS Flow Sensors are easy-to-install flow meters that communicate to the HYDROS app the flow rate of water passing through it. It is safe for use in freshwater and saltwater aquarium systems. The HYDROS Flow Sensors can be used for reactor feed lines and return pumps. Using the HYDROS Flow Sensors can give you peace of mind that your vital aquarium equipment is operating correctly. You can also use the data it collects in the HYDROS app to create rules. For example, if the flow rate were above or below a certain threshold, you can have HYDROS turn off a piece of equipment that is plugged into a Control XP8, Power 4 WiFi power strip, or Smart Plug outlet.
Four Sizes are Available
3/4" Flow Sensor: Flow Range of 40- 800GPH
1" Flow Sensor: Flow Range of 50-1500GPH
1.5" Flow Sensor: Flow Range of 100-2500GPH
2" Flow Sensor: Flow Range of 200-4050GPH
All flow sensors come with schedule 80 PVC Unions, and have an 8' wire length to plug into your Hydros Sense Port. While no power supply is needed, a Hydros Control with an available Sense Port is required for operation.
Hydros Flow Sensor - 1.5 Inch
Overview
The HYDROS Flow Sensors are easy-to-install and measure the flow rate of water passing through it using the HYDROS app.
Available in four sizes: 3/4in (40-800gph), 1in (50-1500gph), 1.5in (100-2500gph), 2in (9200-4050gph)
Monitor Water Flow with
The HYDROS Flow Sensors are easy-to-install flow meters that communicate to the HYDROS app the flow rate of water passing through it. It is safe for use in freshwater and saltwater aquarium systems. The HYDROS Flow Sensors can be used for reactor feed lines and return pumps. Using the HYDROS Flow Sensors can give you peace of mind that your vital aquarium equipment is operating correctly. You can also use the data it collects in the HYDROS app to create rules. For example, if the flow rate were above or below a certain threshold, you can have HYDROS turn off a piece of equipment that is plugged into a Control XP8, Power 4 WiFi power strip, or Smart Plug outlet.
Four Sizes are Available
3/4" Flow Sensor: Flow Range of 40- 800GPH
1" Flow Sensor: Flow Range of 50-1500GPH
1.5" Flow Sensor: Flow Range of 100-2500GPH
2" Flow Sensor: Flow Range of 200-4050GPH
All flow sensors come with schedule 80 PVC Unions, and have an 8' wire length to plug into your Hydros Sense Port. While no power supply is needed, a Hydros Control with an available Sense Port is required for operation.
Hydros Flow Sensor - 2 Inch
Overview
The HYDROS Flow Sensors are easy-to-install and measure the flow rate of water passing through it using the HYDROS app.
Available in four sizes: 3/4in (40-800gph), 1in (50-1500gph), 1.5in (100-2500gph), 2in (9200-4050gph)
Monitor Water Flow with
The HYDROS Flow Sensors are easy-to-install flow meters that communicate to the HYDROS app the flow rate of water passing through it. It is safe for use in freshwater and saltwater aquarium systems. The HYDROS Flow Sensors can be used for reactor feed lines and return pumps. Using the HYDROS Flow Sensors can give you peace of mind that your vital aquarium equipment is operating correctly. You can also use the data it collects in the HYDROS app to create rules. For example, if the flow rate were above or below a certain threshold, you can have HYDROS turn off a piece of equipment that is plugged into a Control XP8, Power 4 WiFi power strip, or Smart Plug outlet.
Four Sizes are Available
3/4" Flow Sensor: Flow Range of 40- 800GPH
1" Flow Sensor: Flow Range of 50-1500GPH
1.5" Flow Sensor: Flow Range of 100-2500GPH
2" Flow Sensor: Flow Range of 200-4050GPH
All flow sensors come with schedule 80 PVC Unions, and have an 8' wire length to plug into your Hydros Sense Port. While no power supply is needed, a Hydros Control with an available Sense Port is required for operation.
Hydros Flow Sensor - 3/4 Inch
Overview
The HYDROS Flow Sensors are easy-to-install and measure the flow rate of water passing through it using the HYDROS app.
Available in four sizes: 3/4in (40-800gph), 1in (50-1500gph), 1.5in (100-2500gph), 2in (9200-4050gph)
Monitor Water Flow with
The HYDROS Flow Sensors are easy-to-install flow meters that communicate to the HYDROS app the flow rate of water passing through it. It is safe for use in freshwater and saltwater aquarium systems. The HYDROS Flow Sensors can be used for reactor feed lines and return pumps. Using the HYDROS Flow Sensors can give you peace of mind that your vital aquarium equipment is operating correctly. You can also use the data it collects in the HYDROS app to create rules. For example, if the flow rate were above or below a certain threshold, you can have HYDROS turn off a piece of equipment that is plugged into a Control XP8, Power 4 WiFi power strip, or Smart Plug outlet.
Four Sizes are Available
3/4" Flow Sensor: Flow Range of 40- 800GPH
1" Flow Sensor: Flow Range of 50-1500GPH
1.5" Flow Sensor: Flow Range of 100-2500GPH
2" Flow Sensor: Flow Range of 200-4050GPH
All flow sensors come with schedule 80 PVC Unions, and have an 8' wire length to plug into your Hydros Sense Port. While no power supply is needed, a Hydros Control with an available Sense Port is required for operation.
Hydros Force Port 24v Adapter Cable
Overview
This HYDROS Force Port Adapter Cable (72 inches long) is designed to directly connect the Kraken to power popular 24V aquarium equipment.
The eight available orange 24V Force Ports on the Kraken can power DC pumps, lights, or any device where the power supply output is 24V.
It features a GX12-4 connector on one end and a standard female 5.5mm x 2.1mm barrel connector on the other to supply power to your 24V device while replacing the device's power brick. This cable is NOT suitable for 12V applications.
Hydros iV Isolated Testing Vessel iV is an HYDROS Drive Port add-on accessory for the Control X10 to Isolates pH, ORP, conductivity/salinity readouts, and facilitates automatic alkalinity testing.For precise pH and Conductivity readings, utilize the HYDROS iV. This add-on ensures that the test sample is physically separated, preventing any electronic interference from other equipment in the aquarium system. This guarantees more reliable data by eliminating any potential issues. Made in the USA utilizing additive manufacturing techniques. Hydros iV Features Isolates pH and Conductivity Readings from the Aquarium for Interference-free Measurement* Automatic Alkalinity Testing* Mixes Test Sample Stable Tabletop Base and Surface Mountable Directly Power by HYDROS Drive Port *Dosing pump(s), controller, pH, and conductivity probes are not included and are sold separately. Hydros iV Specifications Dimensions (LxWxH): 4.5 x 3.5 x 7.5in (not including Probes and tubing) Available Holders: Two Probes and Four Acrylic Tubing Beaker size: 150ml Cord Length: 6ft Includes: Glass Beaker, Mixing Pill, and 500ml of Pre-Mixed kH Testing Reagent
Hydros iV Pro Isolated Testing Vessel
Overview
HYDROS iV PRO Isolated Testing Vessel is a precision-engineered solution for reef tank automation that ensures your water testing is clean accurate and repeatable. Built to integrate seamlessly with the HYDROS Control ecosystem this chamber isolates water samples from your main system to eliminate cross contamination turbulence and microbubbles that can affect sensitive test results.
Perfect for alkalinity tests and other automated parameter checks the iV PRO provides a dedicated chamber for clean water access helping your sensors and dosing systems operate at peak accuracy. This professional-grade vessel is ideal for hobbyists and reef keepers who demand data they can trust.
Key Features
Purpose-built for HYDROS automated testing systems
Maintains isolated testing to avoid cross contamination
Enhances accuracy by eliminating flow-based reading interference
Supports precise sensor readings and reliable dosing operations
Simple integration with existing HYDROS gear
Compact durable and made from reef-safe materials
Recommended Uses
Alkalinity monitoring with auto testers
Sensor calibration zones for pH ORP or conductivity probes
Dosing control to prevent chemical cross-mixing
Dedicated low-flow sample environment away from display tank
What's Included
1x HYDROS iV PRO Isolated Testing Vessel
2x HYDROS bulkhead fittings
2x Tubing inserts for flow control
Mounting bracket and screws
Quick start installation guide
Why Choose iV PRO
Precision reefkeeping requires stable and trustworthy data. The HYDROS iV PRO gives you the control and isolation needed to optimize automated testing and dosing with confidence. Say goodbye to skewed readings
Hydros Kraken Force Port Power Cable
Overview
This HYDROS Force Port Power Cable is used to connect the Kraken to power a WaveEngine LE, WaveEngine, XD, or Control X10. This 6ft cable has two 4-pin GX12-4 fittings.
One end attaches to any of the 8 Force Ports on the Kraken and the other end to the power port on any HYDROS Control Power Port Only (WaveEngine LE, WaveEngine, XD, or Control X10).
Hydros Kraken Power Center
Overview
The Kraken introduces a new concept in aquarium controllers and provides high-power 24V DC switched outputs and a large heavy-duty power supply. This allows "power bricks" and "wall warts" to be removed from aquarium systems, significantly reducing wire clutter.
Hydros Kraken is Ultimate Aquarium Power Strip System Critical Equipment
The HYDROS Kraken is an eight Force Port (24V DC) energy center and controller hybrid specifically designed to replace the power supplies of equipment like flow pumps, return pumps, and LED lights. Each individually controlled Force Port is built into the HYDROS controller for the highest level of security. The Kraken has an external industrial-grade Meanwell power supply with a 20amp/380w max power capacity, and it is designed to pass ETL/UL certification. Besides powering on and off the controllable Force Ports, the Kraken also has four 12V Drive Ports for cabinet lighting, auto-top-off (ATO) pumps, and solenoids. The HYDROS Kraken is passively cooled, and the controller runs silently with its isolated power circuitry. Best of all, each of the eight Force Ports offer individual power monitoring. Besides reducing the amount of 24V power bricks lying around the aquarium, the HYDROS Kraken is also a fully functioning HYDROS system controller capable of taking over intelligent decisions based on the status of other HYDROS devices within the Collective. The two HYDROS Command Bus Ports on the Kraken allow for a wired connection to any other HYDROS controller to form a collective of all Controls for the ultimate fail safe. system. Control and monitor your Kraken power center from anywhere in the world using the technologically advanced HYDROS cloud-based app. The Kraken can also monitor and wireless control up to eight HYDROS WiFi devices.
Features
Power up to 20 amps of system-critical life support equipment
Eliminates clutter by removing the need for eight individual 24V power supplies
The Kraken is a full brain that can share and take over the decision-making of a HYDROS Collective
Control up to eight WiFi devices like fish feeders, smart outlets, and even additional WiFi power strips
Command Bus Port provides power to add redundancy power to your HYDROS Collective
Designed to pass ETL/UL Certification
Universal voltage works with both 110 and 220V
External Industrial Grade Meanwell Super Brick
No noisy fans, the Kraken is entirely passively cooled
Optical isolation between the power circuitry and the control circuitry. This provides safety failure and isolates the control circuitry to reduce noise.
Engineered, built, and supported in the USA.
Force Ports 8 Available
Eight controllable DC power ports, each with individual power monitoring capabilities to safely manage aquarium equipment like lighting, water pumps, protein skimmers, filters, and much more using 24V power. Each high-current 24-volt Force Port provides up to 10amps of 24V DC power to eliminate equipment's "power bricks" and/or "wall warts" that are typically required to run.
Hydros Kraken Force Port Examples Include
Flow pumps 24V return pumps Measurement systems Other Hydros devices Controllers Small to medium-sized aquarium lightsDrive Ports 4 Available
The Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported include: Auto Top-Off (ATO) pumpsDosing pumpsCooling fansCabinet LED lightsSolenoids to control reverse osmosis systemsSteering valves and relays stirrersHydros iV testing vesselBattery Backup Port 1 Available
A specific connection for an external 12V Lead Acid Battery to keep your system alive during power failures. A battery will keep the entire HYDROS system running in Low Power Mode during a power failure. An internal trickle charger keeps these batteries ready to use. The voltage and current on the battery are monitored and reported to the user. This battery can be as large or small as you choose, from small sealed lead acid batteries to large arrays of boat batteries. The Kraken's internal charger can be disabled if you prefer to use a battery charger.
Command Bus 2 Available
The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
External Super Brick 1 Available
A large 24V "super brick" IP65-rated industrial power supply to run all the outputs and the entire HYDROS system. The Super Brick can provide up to 20 Amps of 24 Volt DC power (480 watts). Supply is manufactured by Meanwell, a highly trusted and regarded power supply company.
Specifications
Max Per Force Port: 10A
Total Max Amperage: 20A
Dimensions 9.5 x 4.75 x 3.2 (LxWxH)
Hydros Launch
Overview
The Launch is the perfect starting point for aquarium control. It measures pH and temperature, controls four outlets, and connects to eight Wi-Fi devices. With additional accessories, it can detect leaks, monitor water levels, track salinity, and more.
About Aquarium Controller
The HYDROS Launch is a multifaceted aquatic support system that combines various features into a single controller. It's an all-in-one solution that allows you to manage a wide range of aquarium functions easily. The HYDROS Launch includes a pH or ORP port, a salinity probe port (salinity probe sold separately), four universal sense ports, four 12V drive ports, 0-10V input control, and four controllable AC Outlets built directly into the controller. It's a great starting point for anyone entering the HYDROS platform. With the HYDROS Launch, you can easily monitor temperature, receive leak notifications, track pH or ORP levels, and power up to four system-critical support devices. You can also expand its capabilities by adding accessories to test salinity and alkalinity, monitor water levels, detect leaks, and power other control devices. Whether you have a saltwater aquarium, freshwater tank, or pond, the Launch can be used as a standalone controller or integrated with other HYDROS Controllers to create a more comprehensive system.
is Versatile and Expandable without Extra Modules
Use any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Drive Port - 4 AvailableThe Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported include:
Auto Top-Off (ATO) pumps
Cooling fans
Cabinet LED lights
Solenoids to control reverse osmosis systems
Hydros IV
Steering valves and relays
0-10V PortThe HYDROS Control 4 has 0-10V I/O (input and output) ports that allow it to control and receive commands from other HYDROS devices and accessories from other brands. A legacy automation system can provide input via the 0-10V Ports. They can control variable speed pumps and can also be used to monitor simple switch closures, like push buttons or float switches.Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe. Sense Port - 4 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.Hydros Controller Sense Ports currently supportTemperature probesOptical level sensors (single and dual) Capacitive non-contact liquid level sensorsRope leak detectorsPoint leak detectorsFlow rate sensorsMagnetic switchesPush-button switchesSalinity Probe Port - 1 AvailableThe Salinity Probe is a special probe port for use with conductivity probes to monitor the salinity of your aquarium's water. Salinity Probe Kit is not included but is required to monitor Salinity.Isolated Testing VesselThis add-on ensures that the test sample is physically separated, preventing any electric interference from other equipment in the aquarium system. HYDROS iV is not included but recommended. switches.pH/ORP Probe Port - 1 Available One of the most remarkable ports on the HYDROS Launch is the Probe Port. You can connect an ORP or a pH probe to the Probe Port but, this is no ordinary pH input! The circuitry is based on an ultra-high-quality input chip specifically designed for these types of probes. Each pH input provides digital galvanic isolation from the rest of the system. Galvanic isolation prevents interference with other accessories connected to the system like motors and pumps. Digital Galvanic isolation preserves the accuracy of the measurement by converting the signal to a digital domain before crossing the isolation threshold. Controllable AC Power Outlets - 4 AvailableFour controllable AC power outlets to safely control aquarium equipment like heaters, lighting, water pumps, protein skimmers, filters, and pretty much anything else.
FeaturesPower up to 14 amps of system-critical life support equipmentThe Control Launch is a full brain that can share and take over the decision-making of a HYDROS CollectiveControl up to 8 WiFi devices like fish feeders, smart outlets, and even additional WiFi power stripsCommand Bus port provides power add redundancy power to your HYDROS CollectiveDesigned to pass ETL/UL CertificationUniversal voltage works with both 110 and 220VBuilt- n 60W Meanwell Power SupplyNo noisy fans, the Launch is completely passively cooledOptical isolation between the power circuitry and the control circuitry. This provides safety failure, and it isolates the control circuitry to reduce noise. Engineered, assembled, and supported in the USA.Specifications
Max Per Relay: 8A
Total Max Amperage: 14A
8 - Controllable Power Outlets - Eight controllable AC power outlets each with individual power monitoring capabilities to safely manage aquarium equipment like heaters, lighting, water pumps, protein skimmers, filters, and pretty much anything else.
2 - Command Bus - The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Up to 8 WiFi Devices - Connect up to 8 WiFi devices for added modular control on additional equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately).
1 Year manufacturers limited warranty
Versatile and Expandable without Extra Modules
The HYDROS Launch can be used as a standalone controller for saltwater aquariums, freshwater tanks, pond applications, or it can be added to other HYDROS Controls to build a more extensive system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
The HYDROS Leak Detection Sensor is a solid surface leak detector that can sense when freshwater or saltwater is underneath it and use that information to protect your aquarium, home, or office from total disaster.The way it works is simple: plug the sensor into any Sense Port on a HYDROS OS device (like the Control 2 or Control 4). It does not require any additional power source. Next, place the leak detector in a place that makes sense: next to your sump, under your stand, on the lid of a protein skimmer, under your RO/DI system or saltwater mixing station, next to a freshwater ATO reservoir, underneath your carpet, or wherever else there is a potential for leaks. Finally, configure the HYDROS app to perform whatever action(s) you want to happen when a leak is detected: flash a specific light color on your HYDROS controller, turn off a pump, shut down your protein skimmer, send you a mobile alert so you can come home or ask a friend to check on the tank. It's easy to do and you're in control.One common complaint about aquarium leak detectors currently on the market is that they rust on the bottom. Not the HYDROS Leak Detection Sensor. It is completely encapsulated with a safety seal that makes the unit impregnable. This isn't a product you're going to need to replace. It's built to stand the test of time. You can connect as many Leak Detection Sensors as you have Sense Ports available. Using WiFi Power 4 power strips and Smart Plugs, you can power off equipment in another room if a leak is detected. You could have a specific light turn on in your living room or bedroom if a leak is detected. With HYDROS, you could can all sorts of clever stuff to make sure you're in the know should the worst happen!The HYDROS Leak Detection Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Leak Detection Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor. Get alerted remotely should disaster strike and take correction action with HYDROS!
Hydros Minnow
Overview
The Hydros Minnow is an aquarium controller with two micro-liquid dosing pumps for precise dosing of two-part and trace elements. It can handle essential functions for maintaining a healthy aquarium and connect up to four sense port accessories like temperature sensors, flow meters, TDS monitors, leak detectors, and more.
About Aquarium Controller
The HYDROS Minnow features two independent micro-liquid dosing pumps for precise dosing of your preferred liquid supplements, including two-part and trace elements. This highly versatile controller can effortlessly handle essential functions for maintaining a healthy aquarium. With just one HYDROS Minnow, you can dose two separate liquids and four sense port accessories like temperature sensors, flow, TDS monitoring, leak detection, and more. Whether you have a saltwater aquarium, freshwater tank, or pond, the Minnow can be a standalone controller or seamlessly integrated into other HYDROS Controls to create a more comprehensive system. Operating on a HYDROS Safety Net and boasting an IP65 rating, this controller ensures that your equipment and aquatic life thrive in a safe and secure environment. Moreover, all HYDROS products are meticulously engineered, assembled, and supported in the USA.
Features
HYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Micro-liquid Dosers 2 Available
The HYDROS Minnow features two independent micro-liquid dosing pumps for precise dosing of your preferred liquid supplements, including two-part and trace elements for reef aquariums. The Minnow's pumps have the following set speeds: -55, -45, -25, 25, 40, 55 (ml/min).
Features
Quiet Operation
Rotatable Dosing Heads
Exact Metering of Liquids
Color-Coded Dosing Heads and Tubing
Easy to Service
Command Bus 2 Available
The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Sense Port 4 Available
The Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Sense Ports Currently Support
Temperature sensor - Either air or waterFluid level - Optical sensors to measure liquid levelsLeak detection - Monitoring for both point and wide area leak detectionFlow rate - Measures the amount of fluid flowing through a pipeTotal dissolved solids - Dual measurement of the TDS levels from your RODI system Control Up to 8 Wi-Fi Devices
The HYDROS App allows you to create rules and set schedules to control our 4-Outlet WiFi AC Power Strips and Smart Outlets. Quickly turn on or off different pieces of aquarium equipment like pumps, powerheads, lights, heaters, algae scrubbers, UV sterilizers, protein skimmers, and more. *WiFi Power Strip or Control XP8 is required, sold separately
What's Included
Minnow Controller
Power Supply
Two (2) 10ft Color Dosing Tubing
Calibration Beaker
Extend to your HYDROS Rope Leak Sense Port Accessory for those larger areas you want to protect.The HYDROS Rope Leak Detection Sensor is a flexible line that detects the presence of moisture anywhere along the rope. Can sense when freshwater or saltwater is underneath it and use that information to protect your aquarium, home, or office from total disaster.Does NOT include an adapter to connect to the HYDROS Control.
The HYDROS Leak Detection Rope Sensor is the first of its kind in the aquarium industry. The moment water comes into contact with it, that information can be used to alert you on your smartphone, sound an alarm, turn pumps off, and other actions that can protect your aquarium, home, or office from a total disaster.A problem with traditional solid surface leak sensors is that you have to buy several to really feel a sense of security. What are the odds water will pool in the exact spot where a single sensor sits?Another solution we've come up with is a rope-style water sensor. You can wrap it around your aquarium, sump, stand, or wherever else you like. This type of sensor makes a lot more sense when you want leak detection security in a wider area. You can configure the HYDROS app to perform whatever action(s) you want to happen when a leak is detected: flash a specific light color on your HYDROS controller, turn off a pump, shut down your protein skimmer, send you a mobile alert so you can come home (or ask a friend to check on the tank). It's easy to do and you're in control.Just plug the rope sensor into a Sense Port on your HYDROS device. Next, place the rope flat on the surface where liquid detection is desired. If tape is required to hold the rope in place, be sure to only apply it on the ends. You want to expose as much of the sensor as possible for maximum protection. Once the rope sensor is in place, it is very important to test it to ensure it's working properly. To perform a test, open the HYDROS app on your mobile device and configure the Sense port so the rope sensor is on. Drip a bit of tap water across the rope sensor so the black and white sensing cables come into contact with the liquid. Monitor the sensor's status in the HYDROS app to see check if it's reading is dry or wet. If everything looks good, you're done! Dry the cable and you're ready to configure alerts and equipment to take action if a leak occurs.You don't have to occupy another Sense port to secure a larger area. HYDROS Leak Detection Rope Sensors can be daisy-chained together to form a larger perimeter for protection. Got a big tank? You can lengthen the line of defense to lasso around your large aquarium by simply connecting multiple rope sensors together. Leak detector ropes do not need an additional power source, even if you connect them together. Rope leak detectors do not occupy outlets on power strips or require a HYDROS Drive port connection to operate.HYDROS Leak Detection Rope Sensors offer users 24/7 remote monitoring. Be instantly notified at the first sign of a leak so you can prevent a flood. Tap into the HYDROS app to immediately check the status of water parameters, equipment, power strips, and smart plugs. Make decisions based on real-time data to take appropriate corrective actions from anywhere and at any time.10 ways you can use the HYDROS Leak Detector Rope Place it alongside your aquarium Line it outside of your sum Wrap it around a reactor Lay it on the floor in an open area Fit it into a hard-to-read corner Wrap around plumbing pipes Mount it to a controller board Use it in your mixing station Affix it to water supply and return lines Remotely in your garage, bathroom, basement, laundry room, kitchen, or wherever you make or use water.
Hydros Salinity Kit
Overview
Keep track of the salinity in your marine aquarium with the CoralVue s HYDROS Salinity Kit. This kit includes the necessary 28ppt and 35ppt calibration solutions to ensure precise conductivity readings.
What's Included
High-range Conductivity Probe
28 ppt Calibration Solution (100 mL)
35 ppt Calibration Solution (100mL)
Specifications
Range: 20 to 2000mS/cm
Operating Temp: 0-80C
Constant: K=10
Housing: POM
Probe Dimensions: 12 x 145mm
Connection: BNC
Cable Length: 3ft
Installing your
Locate the Salinity BNC socket on the conductivity meter/controller and twist clockwise to make the connection. Perform two-point calibration per meter's operation manual to ensure accuracy. For precise conductivity reading use an isolated testing vessel like the HYDROS iV. This add-on ensures that the test sample is physically separated, preventing any electric interference from other equipment in the aquarium system.
Hydros Sense Port Extension Cable - 9 Foot
Overview
Give your HYDROS sensors the extra reach they need. This 9 ft GX12-4 (4-pin) Sense Port extension lets you keep controllers high and dry while placing sensors exactly where they work best.
Features
Purpose-built 4-pin Sense extension for HYDROS accessories
Nine feet of added length for flexible, safer cable runs
Threaded aviation connector resists vibration and accidental loosening
Compatible with all HYDROS Sense Port accessories
Specifications
Length: 9 ft
Connectors: GX12-4 (Sense Port), male to female
UPC/EAN: 850009641236
Compatibility: HYDROS sensors and accessories using Sense Ports
Directions
Disconnect power from the controller
Thread the GX12 connectors securely; do not cross-thread
Route cables with drip loops and away from heat/salt spray
Power on and confirm each sensor reads correctly in the HYDROS app
The HYDROS Skimmer Sensor serves a very specific and important role: it prevents your protein skimmer from overflowing onto the floor or back into your sump.The way it works is easy: just place the sensor inside any protein skimmer collection cup up to 1/4" thick. There is a magnetic coupling that will sit on the outside of the skimmer cup to keep the sensor securely in place. Once the waste level in the collection cup rises to the point it makes contact with the sensor, it will tell HYDROS to turn the protein skimmer off to prevent overflowing. Your protein skimmer must be plugged into a HYDROS power source, like the Power 4 power strip or Smart Plug, for this sort of skimmer security to operate.The HYDROS Skimmer Sensor plugs into any HYDROS Sense Port and does not require any additional power supply. The optical eye on this sensor is designed to be used inside the collection cup of a protein skimmer, so it's a little different than a standard water level sensor - but purpose-built for this specific and important application. The sensor contains no moving parts that can fail. It's extremely tiny: it's a little over a half-inch thick with a circumference the size of a US penny. The optical eye is magnetically coupled with the magnet side measuring only 1/4" thick. The cord is on the magnet side so installation is easy. You don't need to purchase a new lid for your skimmer or modify the collection cup in any way.The HYDROS Skimmer Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Skimmer Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor. Keep skimmate in the cup and not in the sump with the HYDROS Skimmer Sensor.HYDROS Water Level Sensor Specs Size: Diameter - 0.75" Sensor - 0.55" thick Magnet Mount - 0.25" thick Max Mounting Thickness: 1/4" No Moving Parts Magnetic Attachment Purpose-built to be placed inside the collection cup of a protein skimmer. Attaches to any protein skimmer collection cup: you don't need to purchase a new lid or modify your collection cup for it to work. The HYDROS Skimmer Sensor uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Manufactured by AutoAqua, an official HYDROS Technology Partner.
Hydros Sole
Overview
The HYDROS Sole is an aquarium controller hybrid with a heavy-duty liquid dosing pump designed for continuous dosing tasks in saltwater and freshwater aquariums. It can be used independently or with other HYDROS devices.
About Aquarium Doser
The HYDROS Sole is an aquarium controller hybrid with a heavy-duty liquid dosing pump designed for continuous dosing applications like controlling effluent in a calcium reactor, kalkwasser additions, dosing liquid foods, feeding a sulfur reactor, and performing water changes. The controller is suitable for both saltwater and freshwater aquariums and can be used independently or in conjunction with other HYDROS devices. The Sole can send alerts and notifications, and when used with a HYDROS XP8 or WiFi Power Strip, it can also control outlets for lights, pumps, feeders, and other aquarium accessories.
Hydros Control XD is Versatile and Expandable without Extra Modules
Use any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
Features
HYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Command Bus - 2 AvailableThe Command bus communicates with other HYDROS devices for the ultimate fail safe. and can also power other Control devices.
Continuous Duty Liquid DoserThe HYDROS Sole features one (1) continuous-duty liquid dosing pump that is capable of controlling effluent in calcium or kalkwasser reactors, dosing liquid foods, feeding a sulfur reactor, and performing water changes.
Features
Quiet Operation
Robust Stepper Motor
For Continuous Use
Can Run in Reverse
Includes 1/4" Push-fit Fittings
Easy to Service
Control up to 8 WiFi Devices The HYDROS App allows you to create rules and set schedules to control our 4-Outlet WiFi AC Power Strips and Smart Outlets. Quickly turn on or off different pieces of aquarium equipment like pumps, powerheads, lights, heaters, algae scrubbers, UV sterilizers, protein skimmers, and more.
Accessories currently supported by Drive Ports includeAuto Top-Off (ATO) pumpsCooling fansCabinet LED lightsSolenoids to control reverse osmosis systemsSpecifications
Sole Controller
Dimensions (LxWxH): 6 x 3.6 x 4.125inTubing Size (IDxOD): 3 x 5mm (0.25in Push-fit Fitting) Pump Set Speeds (mL/min): 0.1 to 300
Power Supply
Calibration Beaker
HYDROS Start Aquarium Controller
OverviewThe HYDROS Start is an affordable entry controller that monitors temperature and powers up to four critical devices while leaving room to expand. With built in WiFi control and a simple app you can add sensors for water level leaks flow and more and scale with additional HYDROS gear as your system grows.Features
Four controllable AC outlets to automate heaters pumps lights skimmers and more
Four Sense Ports accept temperature water level leak flow and TDS sensors
Two Drive Ports power 12V devices such as ATO and dosing pumps cooling fans cabinet LEDs and small solenoids
Two Command Bus ports for expansion and redundant failsafe linking with other HYDROS controls
Control up to eight WiFi devices via the HYDROS app with rules schedules and alerts
Fast dual core processor local and cloud control user defined notifications and internal health monitoring
Specifications
SKU: HDRS START
Ports: 4 AC outlets 4 Sense Ports 2 Drive Ports 2 Command Bus
AC Outlet Capacity: 8A max per outlet 14A total
Drive Port Capacity: 1.5A per port 3A total
Dimensions L x W x H: 9.5 x 4.75 x 3.25 in
Power Cord Length: 6 ft
Compatibility and Upgrade PathsWorks with HYDROS accessories including optical level sensors leak detectors flow sensors TDS sensors ATO and dosing pumps fans cabinet LEDs small solenoids and the HYDROS IV. Expand control using HYDROS Smart Plugs 4 Outlet WiFi AC Power Strips and XP8 power centers all managed in the HYDROS app sold separately.Maintenance and CareMount the controller above the waterline with a drip loop keep vents clear and avoid moisture exposure. Do not exceed 8A per outlet or 14A total. Update firmware through the HYDROS app periodically and audit outlet assignments after adding new equipment.Warranty and ServiceBacked by a 1 year limited warranty with support through the CoralVue Support Portal; warranty starts on purchase date and covers defects in materials and workmanship per CoralVue terms.Shipping and Handling NotesShips as an electronic controller; handle gently and keep dry. Verify packaging condition on arrival and install on a stable dry surface away from salt spray and splashes preferably on a GFCI protected circuit.DirectionsMount the controller connect the included temperature sensor plug life support devices into the four AC outlets download the HYDROS app connect Start to WiFi name outputs set schedules and rules and test each fail safe before regular operation.What's Included
HYDROS Start Controller
Temperature Sensor
Hydros System Command Bus Cable - 1 Foot
Overview
Short, tidy link cable for building a HYDROS Collective. The 5-pin Command Bus carries both data and power between HYDROS devices, enabling synchronized control and shared power where supported.
Features
Data + power bus for inter-controller communication
Ideal for side-by-side mounting with minimal slack
Robust 5-pin keyed connectors for secure connections
Engineered for HYDROS Collectives
Specifications
Length: 1 ft
Connectors: HYDROS 5-pin Command Bus (Data + Power)
UPC/EAN: 850009641441
Compatibility: HYDROS devices with Command Bus ports
Directions
Power down all connected HYDROS devices
Connect between Command Bus ports; hand-tighten threaded collars if present
Install Command Bus Terminators on any open ports as required
Restore power and confirm the Collective status in the HYDROS app
Hydros System Command Bus Cable - 14 Foot
Overview
Extra-long Command Bus cable for spanning larger aquarium rooms or fish rooms. Carries both data and power between HYDROS devices so your Collective stays synchronized over distance.
Features
Long-run 5-pin cable for complex or spread-out installs
Data + power capable to reduce separate power bricks where supported
Durable jacket and molded ends handle repeated service
Works across all HYDROS devices with Command Bus ports
Specifications
Length: 14 ft
Connectors: HYDROS 5-pin Command Bus (Data + Power)
UPC/EAN: 850009641472
Compatibility: HYDROS devices with Command Bus ports
Directions
Power off the system before connecting
Attach between Command Bus ports; avoid sharp bends and pull tension
Add Command Bus Terminators to any open ports
Re-energize and check Collective health/status in the HYDROS app
Hydros System Command Bus Cable - 6 Foot
Overview
Mid-length 5-pin Command Bus cable that links HYDROS devices across stands or cabinets, carrying both data and power to form a reliable Collective.
Features
Data + power transmission between HYDROS devices
Flexible routing with reinforced strain reliefs
Secure 5-pin keyed connectors prevent mis-mating
Supports neat, serviceable controller layouts
Specifications
Length: 6 ft
Connectors: HYDROS 5-pin Command Bus (Data + Power)
UPC/EAN: 850009641229
Compatibility: HYDROS devices with Command Bus ports
Directions
Shut down power to the Collective
Plug into Command Bus ports and finger-tighten any retaining collars
Terminate any unused Command Bus ports
Restore power and verify devices appear in the Collective
The HYDROS Slim Temperature Sensor Probe is only 1.6" long and 0.32" wide. It's all-black solid waterproof IP68 construction is built for years of reliable service. It is a "set it and forget it" temperature monitor that requires no calibration or maintenance (except for perhaps the occasional cleaning). The HYDROS Slim Temperature Sensor Probe is included with the Control 2 or Control 4, so if you need a replacement or just want to add another temperature sensor to your system, you can easily do so for a very low price.The Slim Temperature Sensor Probe has a long 79" cord with a GX12 aviation-style connector that plugs into any Sense Port on the Control 2, Control 4, and future HYDROS devices. You can use multiple temperature sensors on your system for safety and redundancy. For example, you can place one in your display aquarium and another in your sump. This can be helpful if your sump is in your basement while the display tank is on another floor of the house. The Slim Temperature Sensor Probe is completely submersible so you can easily place it somewhere discreet, like in the back of an all-in-one aquarium, in the overflow, or tucked away in one of the chambers of your sump.The HYDROS Slim Temperature Sensor Probe is an easy and affordable way to prevent your aquarium water from becoming too cold or too hot. It monitors the water temperature in your aquarium so you can keep it within the safe zone for fish, coral, and inverts. The probe plugs into any Sense Port on a HYDROS device and does not require any additional power source.You can configure the HYDROS app so that if the water temperature is higher than 82F or lower than 78F (for example), it can send you a mobile alert to let you know. You can also set it up so that outlets that have a heater, chiller, or fan plugged into them turn off when the temperature is outside the safe zone. Your heating and cooling equipment must be plugged into a HYDROS power source, like the Power 4 power strip or Smart Plug, for this sort of automation to occur. The probe contains no moving parts that can fail. It provides peace of mind that your aquarium water temperature will never drift outside optimal ranges for aquatic life. Keep your aquarium water temperature in the safe zone with the HYDROS Slim Temperature Sensor Probe.Features No moving parts Protects your aquarium from unsafe water temperatures You can use it to shut off a heater, chiller, or fan when the water temperature gets too hot or cold You can set it up so that you'll receive a mobile alert of your water temperature drifts outside the safe zone For freshwater and saltwater aquariums You can run multiple temperature sensor probes for safety/redundancy The HYDROS Slim Temperature Sensor Probes uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Official CoralVue HYDROS Accessory
The HYDROS Temperature Sensor is an easy and affordable way to prevent your aquarium water from becoming too cold or too hot. It monitors the water temperature in your aquarium so you can keep it within the safe zone for fish, coral, and inverts. The sensor plugs into any Sense Port on a HYDROS device (like the Control 2 or Control 4) and does not require any additional power source.The way it works is easy: just place the sensor inside your aquarium or sump. It can be mounted to surfaces up to 1/2" thick. There is a magnetic coupling that will sit outside your tank or sump to keep the sensor securely in place. You can configure the HYDROS app so that if the water temperature is higher than 82F or lower than 78F (for example), it can send you a mobile alert to let you know. You can also set it up so that outlets that have a heater, chiller, or fan plugged into them turn off when the temperature is outside the safe zone. Your heating and cooling equipment must be plugged into a HYDROS power source, like the Power 4 power strip or Smart Plug, for this sort of automation to occur.The HYDROS Temperature Sensor contains no moving parts that can fail. It's extremely tiny: it's a little over a half-inch thick with a circumference the size of a US penny. The magnet side measures only 1/4" thick. The sensor is easy to place, easy to move, and easy to clean. It provides peace of mind that your aquarium water temperature will never drift outside optimal ranges for aquatic life.The HYDROS Temperature Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Temperature Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor. Keep your aquarium water temperature in the safe zone with the HYDROS Temperature Sensor.HYDROS Temperature Sensor Specs Size: Diameter - 0.75" Sensor - 0.55" thick Magnet Mount - 0.25" thick Max Mounting Thickness: 1/2" No Moving Parts Magnetic Attachment Protects your aquarium from unsafe water temperatures You can use it to shut off a heater, chiller, or fan when the water temperature gets too hot or cold You can set it up so that you'll receive a mobile alert of your water temperature drifts outside the safe zone For freshwater and saltwater aquariums The HYDROS Temperature Sensor uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Manufactured by AutoAqua, an official HYDROS Technology Partner.
Hydros Triple Optical ATO Kit
Overview
HYDROS Triple Optical ATO Kit delivers advanced and reliable auto top-off protection for your aquarium system. Designed to integrate seamlessly with HYDROS Controllers, this kit uses three highly accurate optical sensors to monitor water levels and provide redundant safeguards-preventing overfilling and protecting your livestock.
With its triple-sensor design, this ATO system offers a level of safety and precision beyond standard two-sensor setups. The first sensor activates the fill pump when water drops, the second confirms proper operation, and the third acts as a failsafe-offering multilayered protection you can trust. Easy to install and configure using the HYDROS App, this kit supports long-term reef stability by keeping salinity consistent and minimizing evaporation effects.
Ideal for sumps, nano tanks, and full-size reef systems, the HYDROS Triple Optical ATO Kit is built for reefers who demand performance and peace of mind from their automation gear.
Key Features
Triple optical sensors provide accurate water level control and redundant safety
Prevents overfills dry runs and pump failures with independent sensor logic
Fully compatible with HYDROS Controllers and configurable through HYDROS App
Simple plug-and-play setup with magnetic sensor mounts
Ideal for saltwater reef tanks AIO systems and freshwater aquariums
Long-lasting durable construction with reef-safe materials
Recommended Uses
Automated top-off systems for marine and reef aquariums
Fail-safe water level monitoring for critical sump applications
Reliable fluid level control for nano tanks and small AIO setups
Custom sensor logic with HYDROS WiFi or Control systems
What's Included
3x HYDROS Optical Water Level Sensors
1x HYDROS DC-powered ATO Pump
Sensor magnet mounts
Mounting accessories and tubing
Power adapter and fittings
Quick-start guide for fast setup
Why Choose
Maintaining stable water levels is vital for a healthy reef tank. Manual top-offs are inconsistent and time-consuming-and many ATO systems fail due to single-sensor limitations. The HYDROS Triple Optical ATO Kit offers unmatched safety by using three separate sensors to ensure top-offs are performed reliably and stopped at the right time. Fully integrated into the HYDROS ecosystem this kit gives reef keepers the confidence to automate their system without sacrificing precision or protection.
Hydros Triple Optical Level Sensor
Overview
The Triple Optical Water Level Sensor plugs directly into a Sense Port on a HYDROS device and does not require an additional power source.
3 Water Level Sensors Added Redundancy
The HYDROS Triple Optical Water Level Sensor can be used for a variety of aquarium applications, such as sensing when your tank needs to be topped off or detecting when a dosing container needs a refill. It plugs into any Sense Port on a HYDROS device (like the Control XS, X2, X4, X10, etc.) and does not require any additional power source. The HYDROS Water Level Sensor contains no moving parts that can fail. The optical eye is magnetically coupled with the magnet side measuring only 1/4" thick. It can be mounted to most clear, tinted, or painted surfaces up to 1/2" thick. The sensor operates in the daytime or complete darkness so it's safe for use hidden inside your aquarium stand or in the back chambers of an all-in-one aquarium. The sensors are easy to place, easy to move, and easy to clean.
Specifications
Diameter: 0.75"
Sensor: 0.75" thick
Magnet Mount: 0.25" thick
Cord length: 75"
Max Mounting Thickness: 1/2"
For freshwater and saltwater aquariums
The HYDROS Water Level Sensor uses a GX12 aviation-style connector so that the Control can maintain its IP65 rating (dust-tight and protected from water spray at any angle).
When the water level in the sump or aquarium drops below theLOW LEVEL (3) on the sensor, it will fill the water till it reachesNORMAL LEVEL (2)SAFETY LEVEL SENSOR (1) is a backup to shut down the feed pump in case of a malfunction; in this case, an alarm can be triggered.
The HYDROS WaveEngine 0-10V Tunze Adapter is required to control Tunze pumps with the WaveEngine.You will also need a HYDROS WaveEngine 0-10V Quad Cable for this application.The way it works is as follows: Connect the Quad Cable to the WaveEngine Connect the Tunze Adapter to the Quad Cable Connect the Tunze Adapter to your Tunze pump controller You can control up to four 0-10V Tunze pumps with the WaveEngine. To do this, you would need the following: 1 x HYDROS WaveEngine 0-10V Quad Cable 4 x HYDROS WaveEngine 0-10V Tunze Adapter* *You don't have to use four pumps. If you only had two pumps, you would only need 1 x Quad Cable and 2 x Tunze Adapters. We used four as our example since you can connect a maximum of four pumps with a Quad Cable.The reason an additional adapter is needed to control Tunze pumps with a WaveEngine is because Tunze pump controllers have a 9-pin jack rather than the more common 3.5 mm stereo jack.Combine your Tunze pumps with pumps from other brands using the HYDROS WaveEngine for a complete water circulation solution!
The HYDROS Water Level Sensor is an optical sensor you can use for a variety of aquarium applications, such as sensing when your tank needs to be topped off or to detect when a dosing container needs a refill. It plugs into any Sense Port on a HYDROS device (like the Control 2 or Control 4) and does not require any additional power source.The HYDROS Water Level Sensor contains no moving parts that can fail. It's extremely tiny: it's a little over a half-inch thick with a circumference the size of a US penny. The optical eye is magnetically coupled with the magnet side measuring only 1/4" thick. It can be mounted to most clear, tinted, or painted surfaces up to 1/2" thick. The sensor operates in the daytime or complete darkness so it's safe for use hidden inside your aquarium stand or in the back chambers of an all-in-one aquarium.You can use the HYDROS Water Level Sensor a multitude of different ways. For example, you could set one up as a high-level sensor and another as a low-level sensor as part of a dual-sensor automatic top-off (ATO) system. You could place these tiny optical sensors inside your dosing containers so you could be alerted when they need to be refilled. You could place a couple in an ATO reservoir: one can tell HYDROS to refill it and the other could prevent it from overflowing. Keep equipment from running dry by having HYDROS cut power to an outlet when the sensor is triggered. The sensors are easy to place, easy to move, and easy to clean.The HYDROS Water Level Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Water Level Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor.HYDROS Water Level Sensor Specs Size: Diameter - 0.75" Sensor - 0.55" thick Magnet Mount - 0.25" thick Max Mounting Thickness: 1/2" Use as High or Low Level No Moving Parts Magnetic Attachment For freshwater and saltwater aquariums The HYDROS Water Level Sensor uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Manufactured by AutoAqua, an official HYDROS Technology Partner.
Hydros Wave Engine v2
Overview
A single app controls a variety of different pumps from your mobile device. Access all the features you desire, without the need for multiple apps, individual controllers, and bulky power supplies that require a "bird's nest" of cables and wires.
Simplifies way we manage flow within our reef aquariums
Until now, limited capabilities have restricted the simple controllers that manage popular pumps like the Maxspect Gyre, Reef Octopus Octo Pulse, TUNZE Turbelle nanostream, and EcoTech VorTech flow pumps. In addition to this convenient and advanced control, you can reduce clutter by eliminating the DC power brick used by modern controllable pumps!
Direct Pump Driver - For many pumps, the HYDROS WaveEngine connects directly to the pump head removing the clutter of the power brick and the control head for these pumps. Maxspect Gyre XF-130 / 230, XF-150 / 250, XF-330 / 350, XF-280*IceCap Gyre 1K, 3K, 2K, 4KReef Octopus RODC-2500, 3500 and 5500, VarioS-2 and 4, Octo Pulse 2 and 4
0-10V Control - Some pumps do not lend themselves to direct drive control due to cabling or other restrictions, but many of these pumps do offer 0-10V controllability. The HYDROS WaveEngine supplies four independent 0-10V outputs to control these pumps. Abyzz PumpsReef Octopus Octo Pulse 2 and 4, VarioS 2, 4, 6 and 8, RODC 2500, 3500 and 5500TUNZE Turbelle nanostream pumps.
Wireless Control - EcoTech Marine Vortech pumps can be controlled using their wireless slave mode so you will no longer need multiple devices to control the most popular flow pump on the market. Better yet, you can make them work in conjunction with most any other brand of controllable powerheads. EcoTech VorTech MP10WQD, MP40WQD and MP60WQD*RF MODULE REQUIRED - not included/supplied by Coralvue at this time.
Control up to 8 WiFi Devices - The new WaveEngine v2 can control up to eight WiFi devices for added modular control on equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately).
Here's what Version 2 can do...
The HYDROS App from CoralVue will completely replace the need for individual manual controllers and apps. By using modern technology, we can easily tap into the native control platform to access all the pre-set flow patterns and modes or create your own! Connect wirelessly to the HYDROS WaveEngine and then communicate with your flow pumps.
Features
Easily add pumps and specify the location of the pump in the aquarium as well as specify min & max speed a pump can run at
Use different brand pumps to work together in different flow pre-set such as sync, anti-sync, triangle wave, square wave, sine wave as well as many other pre-set wave patterns
Create multiple groups
Create and access operational modes such as Feed, Water Change, or Night mode
Monitor power consumption (volts, amps & watts) based on individual pumps & total consumption of all attached pumps
Monitor pump's RPM to ensure maximum performance
EcoTech Vortech pump compatible
Full cloud connectivity so you can control your pumps from anywhere in the world
Real-time notifications of system status & pump performance
Define custom flow patterns of any duration up to 24 hours with 1/1000 second accuracy
Power up to 4 pumps with the Direct Drive ports using a single 100/240V 2.5 amp input power supply (included). The output is 24V/6 amps.
Broad CompatibilityMake pumps from different manufacturers work together to provide a single, integrated flow management system. You can now use a VorTech MP40WQD at one end of your tank and a Reef Octopus Octo Pulse 4 at the other end of the tank and have them work together simultaneously, opposite each other or completely different. Best of all, it isn't limited to two pumps! Add a Maxspect Gyre into the pattern if you want too. Do you have a controllable return pump or skimmerBring them to the party because the HYDROS WaveEngine will control them too! Clutter ReductionThe clutter of power bricks, cables and controllers is becoming an increasing problem for reef keepers. The four pump driver outputs on the HYDROS WaveEngine replace the pump controller, power supplies and any necessary external wireless control modules. Best of all, the HYDROS WaveEngine can run four pumps off a single power supply! Needless to say, it is easy to install. Simply toss out your existing power supplies and controllers, connect the HYDROS WaveEngine and you're ready to start moving water. 0-10V INPUT ControlControl any pump via variable speed INPUT. Unlike other controllers that require intricate programming on pumps connected via 0-10V, the HYDROS WaveEngine allows 0-10V INPUT connected Pumps to take full advantage of all native flow modes and pre-sets without complicated coding.Reverse Pump DriveSome pumps can provide additional pattern options by running in reverse. For example, the Reef Octopus Octo Pulse 4 changes from a highly directed flow to a gentle broad push if you run it in reverse. The HYDROS WaveEngine allows you to take advantage of Reverse Drive to further increase the available flow patterns.Cross Engine SynchronizationMultiple HYDROS WaveEngines can be used to control even larger number of pumps and the patterns will remain perfectly synchronized. A pump connected to HYDROS WaveEngine "A" will run in perfect synchronization with a pump connected to HYDROS WaveEngine "B".Remote AccessA FREE and easy to use iOS and Android compatible app allows you to control everything including flow modes, schedules, pump configuration, as well as monitor performance. You will have no problem with connection because the app can run in cloud mode or local mode. Cloud mode allows you to communicate with your HYDROS WaveEngine when an internet connection is available. The HYDROS WaveEngine system is part of the Amazon Web Services (AWS) and Internet of Things (IoT) platform, guaranteeing high security and reliability. Local control gives you the option of direct access to your control settings in the event your internet connection is unavailable. No matter your situation, the HYDROS WaveEngine will work to keep your tank alive! Real-Time Monitoring and NotificationsYou can set up text message alerts and/or emails to be notified if a pump is blocked or disconnected. If total power failure takes place at your home, bringing down your entire tank and internet connection, you will still be notified via email or text. Do your pumps ever get dirty and drop in performanceThe HYDROS WaveEngine will monitor the power being consumed by each pump along with its shaft RPM and will notify you if the pump's performance is suffering and may require maintenance. Maxspect Gyre 280 pumps can only run at 75% max intensity.PLEASE NOTE: An appropriate pump adapter or 0-10V cable (sold separately) is required to connect pumps directly to the HYDROS WaveEngine.
A Smart and Affordable Way to Power Your Aquarium GearThe HYDROS Power 4 WiFi Power Strip is a smart power bar designed to work with the CoralVue HYDROS platform. The Power 4 has 4 x 120V AC outlets and 4 x USB ports that are WiFi controllable using the free HYDROS app for Android and iOS/Apple mobile devices. You can turn outlets on and off wirelessly over a 2.4 GHz WiFi frequency.The Power 4 has a range of 98 feet, so you can place power strips around your home without any difficulty connecting to your modem or router. Each of the 4 x outlets can be controlled individually while the 4 x USB ports are controlled as one. The 4 x outlets have individual LED indicators and the 4 x USB ports have a single LED indicator. The status LEDs indicate when an outlet is energized.Control and Monitor Aquarium Equipment from Your Mobile DeviceBy using the HYDROS app with the Power 4, you can create rules and schedules to turn on and off different pieces of aquarium equipment, like pumps, powerheads, lights, heaters, algae scrubbers, UV sterilizers, protein skimmers, and whatever else you may want to control on demand or put on a schedule. The USB ports are ideal for connecting and controlling aquarium cooling fans which you can program to turn on if your aquarium water gets too hot and then turn back off automatically when the water drops back within ideal ranges.Control Multiple Power Strips from a Single, Easy-to-Use Mobile AppAnother great thing about the Power 4 is that you can control multiple Power 4 Power Strips from the HYDROS app. You might use a couple of Power 4's to power your display tank, place another in the garage to use for a saltwater mixing station, and have units in each of your children's bedrooms to turn even beginner tanks into smart aquariums. The beauty of it is that you can control all these different outlets that are being used for different purposes using a single app.Be Notified If an Outlet Fails So You Can Take Corrective ActionYou can also monitor the outlets on your Power 4 power strip. If an outlet fails or loses its WiFi connection, you will be immediately notified via alerts to your mobile device. This safety feature can help prevent a tank catastrophe. For example, if the outlet powering your return pump failed, you would receive a notification to let you know something is awry so that you can take corrective action. As a temporary fix, you might decide to turn on all your flow pumps and increase their speed remotely via the HYDROS app to keep the water moving and the temperature stable until you can arrive home to investigate.HYDROS WiFi OutletsThe HYDROS Control system can utilize WiFi-based power outlets as part of its configuration. These outlets can be used to switch lights, pumps, heaters, and other equipment on or off as needed in an aquarium environment.The power outlets connect to the Control device via WiFi. Understandably, there are concerns about the general reliability of these outlets and the possibility of a loss of communication.One thing that should be pointed out is that HYDROS talks to the outlets directly on WiFi. No cloud interaction is involved. Thus, as long as your WiFi hub is operating, the outlets will work even if the outbound Internet connection fails.The following outlines some of the safeguards that have been taken to reduce the probability of failure.MonitoringHYDROS does not treat the outlets passively. Control 2 and Control 4 devices monitor each WiFi outlet continuously at a rate of at least once a second. HYDROS communicates with each outlet and verifies that it is returning the correct status. If the state is incorrect (for example, if the outlet was switched ON or OFF manually), HYDROS will immediately switch the outlet back to where it should be.If the HYDROS Control device cannot communicate or verify the status of an outlet, an alarm will go off, and it will send a notification email or SMS text to the user. This process allows the user to know if an outlet disappears or malfunctions immediately. On the Smart Plug WiFi outlets which support current measurement, HYDROS can also verify if the device's current consumption is within the expected range. So, for example, if a heater is supposed to consume 400 watts, an alert can be sounded if it is less than 350 watts (probably will be zero if it failed).HYDROS Power 4 Strip Specifications Power: AC 120V Outlets: 4 X AC Outlets | 4 X USB Ports Total Power Rating: 10A/1250W Total USB Power: 2A WiFi Frequency: 2.4 GHz Dimensions: 7.8 x 4 x 1.1in Weight: 483g
Hygger 2-in-1 Sponge Filter - Large
Overview
The Hygger aquarium biochemical sponge filter is powered by an air pump that uses the water-lifting effect generated by rising bubbles and drives water flow through the filter sponge and media chamber which can effectively adsorb waste and residual food to achieve the purpose of filtering and purifying water quality for saltwater and freshwater aquariums.
Features
2 in 1 Feature Oxygenation - With built-in a plastic air stone, provides enough bubbles and gentle flow.Filtration - The dense biochemical sponge on the upper layer can effectively absorb impurities, fish waste, and debris, while the circular concave structure increases the filtration surface, which helps improve filtration efficiency.Media Chamber - The extra chamber in the bottom with bio ceramic media which helps breed more beneficial bacteria that the aquarium can utilize.
For Small and Medium-Sized Aquariums This air-powered biochemical filter is 2.9 inches wide and 3.7/5.5 inches tall, making it works well filtering aquariums 1 to 20-gallon in size with under 12"/15" depth, as well as with any low-flow application, like breeding, bettas, snails, shrimp, etc.
Cleaning and Replacement Filter - All the parts included in the aquarium biochemical filter are detachable, which can be easy to assemble and disassemble. It includes two sponges that could be reused, it is recommended to use tank water to wash the filter assembly every 2-4 weeks or whenever you see a decrease in bubbles to ensure the filter works properly.
Specifications
Model Number: HG120-L
Dimension: 6.4"H x 3.9" Diameter
Maximum Aquarium Depth: 26.4" (67cm)
Hygger 2-in-1 Sponge Filter - Medium
Overview
The Hygger aquarium biochemical sponge filter is powered by an air pump that uses the water-lifting effect generated by rising bubbles and drives water flow through the filter sponge and media chamber which can effectively adsorb waste and residual food to achieve the purpose of filtering and purifying water quality for saltwater and freshwater aquariums.
Features
2 in 1 Feature Oxygenation - With built-in a plastic air stone, provides enough bubbles and gentle flow.Filtration - The dense biochemical sponge on the upper layer can effectively absorb impurities, fish waste, and debris, while the circular concave structure increases the filtration surface, which helps improve filtration efficiency.Media Chamber - The extra chamber in the bottom with bio ceramic media which helps breed more beneficial bacteria that the aquarium can utilize.
For Small and Medium-Sized Aquariums This air-powered biochemical filter is 2.9 inches wide and 3.7/5.5 inches tall, making it works well filtering aquariums 1 to 20-gallon in size with under 12"/15" depth, as well as with any low-flow application, like breeding, bettas, snails, shrimp, etc.
Cleaning and Replacement Filter - All the parts included in the aquarium biochemical filter are detachable, which can be easy to assemble and disassemble. It includes two sponges that could be reused, it is recommended to use tank water to wash the filter assembly every 2-4 weeks or whenever you see a decrease in bubbles to ensure the filter works properly.
Specifications
Model Number: HG120-M
Dimension: 6"H x 2.9" Diameter
Maximum Aquarium Depth: 19.7" (50cm)
Hygger 2-in-1 Sponge Filter - Small
Overview
The Hygger aquarium biochemical sponge filter is powered by an air pump that uses the water-lifting effect generated by rising bubbles and drives water flow through the filter sponge and media chamber which can effectively adsorb waste and residual food to achieve the purpose of filtering and purifying water quality for saltwater and freshwater aquariums.
Features
2 in 1 Feature Oxygenation - With built-in a plastic air stone, provides enough bubbles and gentle flow.Filtration - The dense biochemical sponge on the upper layer can effectively absorb impurities, fish waste, and debris, while the circular concave structure increases the filtration surface, which helps improve filtration efficiency.Media Chamber - The extra chamber in the bottom with bio ceramic media which helps breed more beneficial bacteria that the aquarium can utilize.
For Small and Medium-Sized Aquariums This air-powered biochemical filter is 2.9 inches wide and 3.7/5.5 inches tall, making it works well filtering aquariums 1 to 20-gallon in size with under 12"/15" depth, as well as with any low-flow application, like breeding, bettas, snails, shrimp, etc.
Cleaning and Replacement Filter - All the parts included in the aquarium biochemical filter are detachable, which can be easy to assemble and disassemble. It includes two sponges that could be reused, it is recommended to use tank water to wash the filter assembly every 2-4 weeks or whenever you see a decrease in bubbles to ensure the filter works properly.
Specifications
Model Number: HG120-S
Dimension: 4.1"H x 2.9" Diameter
Maximum Aquarium Depth: 15.8" (40cm)
Hygger 3-in-1 Aquarium Gravel Cleaner - Medium
Overview
The Hygger 3-in-1 Aquarium Small Gravel Cleaner offers gravel cleaning waste suctioning and water changing all in one tool for any aquarium.
Features
3 in 1 Siphon FunctionSand Washing - The Hygger aquarium siphon pump helps to remove debris from gravel - all you need to do is simply move the inlet pipe up and down, and the debris can be carried away by the running water, while the gravel falls to the bottom of the aquarium. The removable filter basket inside the gravel washer tube prevents small fish and gravel from being sucked into the aquarium vacuum.Dirt Suction - The duckbill head attachment of the siphon vacuum gravel cleaner can remove the substrate dirt, fish debris, food, and fish waste that build up in the aquarium. It has two pipes to reach where needed and is fast cleaner.Water Changing - This aquarium siphon pump uses a vacuum siphon design to help you change water easily and efficiently. The siphon pump features the latest design to drain your tank in minutes. It makes tank water changes truly hassle-free.
Protects Your Fish - This aquarium siphon cleaner has no electricity and will not harm the fish when used. It includes a 3D filter basket that prevents gravel from jamming the pipe. Not only does it separate and remove debris effectively, but it also protects the fish fry, plants, and gravel from being sucked out. The hose of the vacuum pump is made from high-quality silicone, harmless to fish, and has no peculiar smell.
Easy Installation and Use - The Hygger 3-1 Gravel Vacuum is easy to assemble and disassemble. You can pre-install the siphon balls position to make the operating the gravel vacuum more convenient. First, just squeeze the siphon ball a few times, then the tank water will automatically flow out quickly. When it is in full flow it can drain 30 liters of water in 5 minutes.
Keep Your Hands Free - The flow valve that comes with the gravel cleaner can easily control the suction rate. The hose clamp can affix the hose in the bucket, preventing water from accidentally splashing or dirtying the floor, and keeping your hands free.
Made from Durable Material - This durable aquarium siphon cleaner is made with robust, high-quality PVC. It is able to withstand the regular water changes necessary to keep fish healthy and happy. It is able to take out any dirt or debris and has a long service life.
Hygger 3-in-1 Aquarium Gravel Cleaner - Small
Overview
The Hygger 3-in-1 Aquarium Small Gravel Cleaner offers gravel cleaning waste suctioning and water changing all in one tool for any aquarium.
Features
3 in 1 Siphon FunctionSand Washing - The Hygger aquarium siphon pump helps to remove debris from gravel - all you need to do is simply move the inlet pipe up and down, and the debris can be carried away by the running water, while the gravel falls to the bottom of the aquarium. The removable filter basket inside the gravel washer tube prevents small fish and gravel from being sucked into the aquarium vacuum.Dirt Suction - The duckbill head attachment of the siphon vacuum gravel cleaner can remove the substrate dirt, fish debris, food, and fish waste that build up in the aquarium. It has two pipes to reach where needed and is fast cleaner.Water Changing - This aquarium siphon pump uses a vacuum siphon design to help you change water easily and efficiently. The siphon pump features the latest design to drain your tank in minutes. It makes tank water changes truly hassle-free.
Protects Your Fish - This aquarium siphon cleaner has no electricity and will not harm the fish when used. It includes a 3D filter basket that prevents gravel from jamming the pipe. Not only does it separate and remove debris effectively, but it also protects the fish fry, plants, and gravel from being sucked out. The hose of the vacuum pump is made from high-quality silicone, harmless to fish, and has no peculiar smell.
Easy Installation and Use - The Hygger 3-1 Gravel Vacuum is easy to assemble and disassemble. You can pre-install the siphon balls position to make the operating the gravel vacuum more convenient. First, just squeeze the siphon ball a few times, then the tank water will automatically flow out quickly. When it is in full flow it can drain 30 liters of water in 5 minutes.
Keep Your Hands Free - The flow valve that comes with the gravel cleaner can easily control the suction rate. The hose clamp can affix the hose in the bucket, preventing water from accidentally splashing or dirtying the floor, and keeping your hands free.
Made from Durable Material - This durable aquarium siphon cleaner is made with robust, high-quality PVC. It is able to withstand the regular water changes necessary to keep fish healthy and happy. It is able to take out any dirt or debris and has a long service life.
Hygger 360 Mini Aquarium Powerhead - 1056GPH
Overview
The Hygger mini wave maker generates a surge current that enhances oxygenation near the water surface, promoting fish health and providing a natural current for corals. It also facilitates even water heating.
The adjustable power head helps dislodge debris from gravel and allows you to conceal the wave maker, while its design permits easy repositioning without needing to reach into the water.
Features
Oxygenation & Filtration - The mini wave maker enhances water agitation, which increases oxygen levels. Position it near the water surface to create a surge current. For improved filtration, adjust the power head to direct water flow that dislodges debris from the gravel, which is then drawn into the filter.
360o Flexible Head - Featuring a 360-degree rotatable ball joint, the mini wave maker allows for precise adjustments in any direction. This flexibility helps reduce dead spots in corners and maintains a cleaner tank environment.
Easy to Disassemble & Clean - ETL-certified for high standards, the wave maker includes a durable motor and corrosion-resistant ceramic shaft, suitable for both freshwater and saltwater tanks. The removable protection guard simplifies cleaning.
Easy Installation & Magnetic Base - The magnetic base allows for easy mounting on glass panels 4-10 mm thick. It can be repositioned as needed to find the optimal placement for your tank. The included cotton pad absorbs vibrations, ensuring quieter operation.
Specifications
Power Consumption: 6 Watts (110/120v 60Hz)
Flow Rate: 1056 GPH
Dimensions: 2.6" x 2.16" x 4.7" Maximum Glass Thickness: 0.39" (10mm)
Hygger 360 Mini Aquarium Powerhead - 530GPH
Overview
The Hygger mini wave maker generates a surge current that enhances oxygenation near the water surface, promoting fish health and providing a natural current for corals. It also facilitates even water heating.
The adjustable power head helps dislodge debris from gravel and allows you to conceal the wave maker, while its design permits easy repositioning without needing to reach into the water.
Features
Oxygenation & Filtration - The mini wave maker enhances water agitation, which increases oxygen levels. Position it near the water surface to create a surge current. For improved filtration, adjust the power head to direct water flow that dislodges debris from the gravel, which is then drawn into the filter.
360o Flexible Head - Featuring a 360-degree rotatable ball joint, the mini wave maker allows for precise adjustments in any direction. This flexibility helps reduce dead spots in corners and maintains a cleaner tank environment.
Easy to Disassemble & Clean - ETL-certified for high standards, the wave maker includes a durable motor and corrosion-resistant ceramic shaft, suitable for both freshwater and saltwater tanks. The removable protection guard simplifies cleaning.
Easy Installation & Magnetic Base - The magnetic base allows for easy mounting on glass panels 4-10 mm thick. It can be repositioned as needed to find the optimal placement for your tank. The included cotton pad absorbs vibrations, ensuring quieter operation.
Specifications
Power Consumption: 3 Watts (110/120v 60Hz)
Flow Rate: 530 GPH
Dimensions: 2.6" x 2.16" x 4.7" Maximum Glass Thickness: 0.39" (10mm)
Hygger 5000 Gyre Aquarium Pump
Overview
This advanced wave pump features five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave. It also offers three working modes: feeding mode, night mode, and linkage mode.
Customizable for various aquarium setups, it provides 1-100 levels of flow rate and frequency adjustments.
Features
Multi-Functional Wave Pump - This powerful wave pump offers five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave - and three working modes: feeding mode, night mode, and linkage mode. With adjustable flow rates (1-100 levels) and frequency levels (1-100 levels), it provides extensive customization for your aquarium's needs.
Intelligent LED Controller - The wave pump features an intelligent LED controller that allows you to switch between different modes to simulate natural ocean waves, creating a dynamic aquatic environment.
Pattern Wave Effects - The Hygger aquarium wave pump comes with a robust magnetic base, enabling versatile placement in the tank for varied effects:Upper Position: Creates different wave shapes.Middle Position: Produces a continuous stream of small bubbles, mimicking ocean effects.Bottom Position: Dislodges debris and removes accumulated substances, helping to maintain a clean tank.
Super Silent Operation - Utilizing sine wave control technology, the wave pump operates with minimal noise. Its rotatable head generates waves from multiple directions, making it ideal for creating a natural and quiet environment for aquatic life.
Specifications
Model Number: HG070-12W
Flow Rate: 1321GPH (5000 LPH)
Dimensions: 4.8"L x 1.4"W x 1.3"H Maximum Glass Thickness: 0.315" (8mm)
Recommended Aquarium Size: < 60 Gallons
Hygger 6-in-1 Aquarium Cleaning Tool Kit
Overview
The Hygger aquarium cleaning tool kit includes a fishnet, an algae scraper, two sponges, a tube brush, and a gravel rake. It's perfect for cleaning and maintaining the aquarium.
Features
Telescopic Handle - Special buckle design, extends easily while the attachments fit firmly and do not fall off. It can be adjusted from 1.95 feet to 2.95 feet. It's long enough to clean up to a depth of 2.65-feet, without getting your hands wet.
Durable Material - The handle pole is made of sturdy carbon fiber composite for long-lasting use for many years without bending or breaking. Attachments fit firmly to the pole, and won't fall off. It's the perfect cleaning tool for all aquarium hobbyists.
Less Water Intake - Scientific structural design reduces the water intake. The handle poles and connection attachments fit together properly, so water will not get into the pole when put together properly to avoid making a mess when removed from the aquarium.
Specifications
Model Number: HG816
1 x Handle (1 PC handle head with tube
1 PC connection stick tube
1PC connection head)
1 x Fishnet
1 x Algae scraper
1 x Tube brush
1 x Gravel rake
1 x Flat sponge
1 x Right-angle sponge
1 x User manual
Hygger 7000 Gyre Aquarium Pump
Overview
This advanced wave pump features five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave. It also offers three working modes: feeding mode, night mode, and linkage mode.
Customizable for various aquarium setups, it provides 1-100 levels of flow rate and frequency adjustments.
Features
Multi-Functional Wave Pump - This powerful wave pump offers five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave - and three working modes: feeding mode, night mode, and linkage mode. With adjustable flow rates (1-100 levels) and frequency levels (1-100 levels), it provides extensive customization for your aquarium's needs.
Intelligent LED Controller - The wave pump features an intelligent LED controller that allows you to switch between different modes to simulate natural ocean waves, creating a dynamic aquatic environment.
Pattern Wave Effects - The Hygger aquarium wave pump comes with a robust magnetic base, enabling versatile placement in the tank for varied effects:Upper Position: Creates different wave shapes.Middle Position: Produces a continuous stream of small bubbles, mimicking ocean effects.Bottom Position: Dislodges debris and removes accumulated substances, helping to maintain a clean tank.
Super Silent Operation - Utilizing sine wave control technology, the wave pump operates with minimal noise. Its rotatable head generates waves from multiple directions, making it ideal for creating a natural and quiet environment for aquatic life.
Specifications
Model Number: HG070-18W
Flow Rate: 1850GPH (7000 LPH)
Dimensions: 8.5"L x 2"W x 1.3"H Maximum Glass Thickness: 0.39" (10mm)
Recommended Aquarium Size: < 135 Gallons
Hygger Glass Fish Bowl
Overview
The aquarium fish bowl from Hygger fits almost anywhere and is the perfect size for small fish! It is suitable for keeping bettas, goldfish, and shrimp. It is also a creative gift idea for your children.
Features
Crystal Clear Glass Bowl - Good crystal-clear clarity offers a panoramic view of the fish bowl. The glass thickness is about 5 mm. The glass bowls are easy to clean with water.
Small Oblate Shape - It does not take up much space to place the small round fish bowl virtually anywhere. It is 7.9 inches in height, 5.9 inches in depth, while being 3 inches in width. You can place it on the table, windowsill, shelf, etc.
Prepared Glass Kits - Comes with blue glass beads and a plastic tree ornament, and you can add 0.5-0.6 gallons of water for small fish.
SpecificationsModel Number: HG975Dimensions: 7.9 x 5.9 x 3"Glass Thickness: 5mmCapacity: 0.75 gallonsBowl Weight: 2.66lbsIncludes: 1 x Fish Bowl1 x Plastic Plant1 x 0.88 Aquarium Gravel1 x User Manual
Hygger 9000 Gyre Aquarium Pump
Overview
This advanced wave pump features five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave. It also offers three working modes: feeding mode, night mode, and linkage mode.
Customizable for various aquarium setups, it provides 1-100 levels of flow rate and frequency adjustments.
Features
Multi-Functional Wave Pump - This powerful wave pump offers five wave modes - pulse wave, sine wave, constant wave, random wave, and cross flow wave - and three working modes: feeding mode, night mode, and linkage mode. With adjustable flow rates (1-100 levels) and frequency levels (1-100 levels), it provides extensive customization for your aquarium's needs.
Intelligent LED Controller - The wave pump features an intelligent LED controller that allows you to switch between different modes to simulate natural ocean waves, creating a dynamic aquatic environment.
Pattern Wave Effects - The Hygger aquarium wave pump comes with a robust magnetic base, enabling versatile placement in the tank for varied effects:Upper Position: Creates different wave shapes.Middle Position: Produces a continuous stream of small bubbles, mimicking ocean effects.Bottom Position: Dislodges debris and removes accumulated substances, helping to maintain a clean tank.
Super Silent Operation - Utilizing sine wave control technology, the wave pump operates with minimal noise. Its rotatable head generates waves from multiple directions, making it ideal for creating a natural and quiet environment for aquatic life.
Specifications
Model Number: HG070-25W
Flow Rate: 2380GPH (9000 LPH)
Dimensions: 11.1"L x 2.4"W x 1.3"H Maximum Glass Thickness: 0.47" (15mm)
Recommended Aquarium Size: < 265 Gallons
Hygger Adjustable Cooling Fan
Overview
The Hygger Adjustable Cooling Fan is a quiet fish tank cooling fan with a 7-wing fan wheel that pushes large air volume at the outlet, It is designed to be energy saving with low noise generation.
It comes with a controller to adjust the time on and speed. The fan also comes with an automatic switch so there is no need to switch the fan on every day,
The Hygger Aquarium Cooling Fan is suitable for freshwater and saltwater aquariums less than 31.5 inches long and 0.45 inches (1.1 cm)
Features
One Controller can control up to 3 Fans
Controller includes 5 time periods of operations from 30mins - up to 12 hours
5 different levels of speed
Fan has an 180 degree adjustable head to accommodate most set-ups.
Sturdy ABS plastic shell, all-copper core motor and FDB bearings ensure a long life and a quality build.
Specifications
Dimensions (excluding mount): 5.1" x 5.1" x 1.5"
Input: 100-240V
Output: 12v / 2A
For aquarium surface area of 12" or less
Maximum glass thickness: 0.45" (11mm)
