Neptune AquaBus Cable - 3 Foot Male/Male
Overview
3 Foot Male/Male Neptune Apex AquaBus cable.
Used to connect an AquaBus module (PM1, EB8, etc) to another AquaBus Module or Apex base unit.
Neptune 24V Power Supply
Overview
Replacement power supply for any 24V Neptune Apex product.
This includes the GRO LED lights, PMUP pumps, solenoid valves, etc.
Neptune Flow Monitoring Kit (FMK)
Overview
Start monitoring the flow in your aquarium with the Neptune Systems FMK (Flow Monitoring Kit).
FMM FLUID MONITORING MODULE IT DOES SO MUCH!
The FMM (Fluid Monitoring Module) is a multi- purpose module that, with the help of various accessories, enables your Apex to do:
Flow Monitoring
Leak Detection
Water Level Detection
Power 24VDC accessories
Future sensors
FMK Flow Sensors
Return Pump: Measuring the flow of your aquarium's main return pump is an incredibly useful piece of information. The key benefit would be to have the Apex notify you the instant the flow stops for any reason - usually the result of a failed or faulty pump. Furthermore, an indication of a reduced flow rate could be used to determine that the pump or the lines are dirty or are becoming clogged with algae, debris, animals, or the growth of organisms inside your plumbing.Auxiliary pumps on reactors and the like: This is a very handy application for the FMM. Place a flow sensor on a device like a carbon/gfo/biopellet reactor and it serves many purposes. First off, you will know if your pump is not flowing correctly or failed altogether. Next, you can easily fine-tune the flow into the reactor by watching the dashboard tile on your Apex. Finally, you can know when the reactor is becoming clogged with detritus or possibly channeling has occurred by an alert on your Apex or by monitoring your dashboard. Put a flow sensor inline to your device, plug it in to the FMM, and see exactly the flow rate of the water (any aquarium fluid really) going through that sensor. The industrial-grade flow sensors use either a turbine or paddle-wheel mechanism (depending on the model) to measure the flow. It is important to note that the flow rate that will be reported back to you from the flow sensors will likely be far lower than you expect or what is printed on the pump label or documentation. This is due to head pressure loss from physical height differences, long runs, restrictions such as ball valves, fittings like elbows, tees, and reducers, and then finally the loc-line many use as the entry point into their tanks. As an example, a pump rated at 3200gph will likely be showing less than half that amount in nearly all applications.Four Ports: The FMK comes with three flow sensors but the FMM has a total of four ports. This means you have one port free to use for another purpose. Buy additional flow sensors (available also in 2" and 1/4" sizes) or choose from other options available and add even more functionality!Each Neptune FMK includes following items
1 - FMM (Fluid Monitoring Module) - is a module that connects to any Apex (Apex(2016), Apex Classic, Apex Lite, Apex Jr.) - via it's AquaBus port providing four multi-function monitoring ports that can be used for flow sensors, water-level sensors, leak detection sensors and possibly future products as well.
1 - 1" Flow Sensor - This flow sensor connects to the FMM, monitors the flow of water through the device, and then reports it back to your Apex via the FMM. This sensor is most often used to measure the flow in the main return line of a standard-sized aquarium.
2 - 1/2" Flow Sensors - This flow sensor connects to the FMM, monitors the flow of water through the device, and then reports it back to your Apex via the FMM. Two of these are included in the FMK. These sensors are perfect for attaching to devices such as media reactors, biopellet reactors, etc.
2 - 1" Unions - To connect your FS-100 Flow sensor, we have included in the FMK, two 1BSPT -> 1Slip PVC Unions. (North American markets only)
4 - 1/2" Adapters - To connect your two FS-50 Flow sensors, we have included in the FMK, two 1/2BSPT -> 1/2Slip PVC Adapters.(North American markets only)
Hydros Wave Engine v2
Overview
A single app controls a variety of different pumps from your mobile device. Access all the features you desire, without the need for multiple apps, individual controllers, and bulky power supplies that require a "bird's nest" of cables and wires.
Simplifies way we manage flow within our reef aquariums
Until now, limited capabilities have restricted the simple controllers that manage popular pumps like the Maxspect Gyre, Reef Octopus Octo Pulse, TUNZE Turbelle nanostream, and EcoTech VorTech flow pumps. In addition to this convenient and advanced control, you can reduce clutter by eliminating the DC power brick used by modern controllable pumps!
Direct Pump Driver - For many pumps, the HYDROS WaveEngine connects directly to the pump head removing the clutter of the power brick and the control head for these pumps. Maxspect Gyre XF-130 / 230, XF-150 / 250, XF-330 / 350, XF-280*IceCap Gyre 1K, 3K, 2K, 4KReef Octopus RODC-2500, 3500 and 5500, VarioS-2 and 4, Octo Pulse 2 and 4
0-10V Control - Some pumps do not lend themselves to direct drive control due to cabling or other restrictions, but many of these pumps do offer 0-10V controllability. The HYDROS WaveEngine supplies four independent 0-10V outputs to control these pumps. Abyzz PumpsReef Octopus Octo Pulse 2 and 4, VarioS 2, 4, 6 and 8, RODC 2500, 3500 and 5500TUNZE Turbelle nanostream pumps.
Wireless Control - EcoTech Marine Vortech pumps can be controlled using their wireless slave mode so you will no longer need multiple devices to control the most popular flow pump on the market. Better yet, you can make them work in conjunction with most any other brand of controllable powerheads. EcoTech VorTech MP10WQD, MP40WQD and MP60WQD*RF MODULE REQUIRED - not included/supplied by Coralvue at this time.
Control up to 8 WiFi Devices - The new WaveEngine v2 can control up to eight WiFi devices for added modular control on equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately).
Here's what Version 2 can do...
The HYDROS App from CoralVue will completely replace the need for individual manual controllers and apps. By using modern technology, we can easily tap into the native control platform to access all the pre-set flow patterns and modes or create your own! Connect wirelessly to the HYDROS WaveEngine and then communicate with your flow pumps.
Features
Easily add pumps and specify the location of the pump in the aquarium as well as specify min & max speed a pump can run at
Use different brand pumps to work together in different flow pre-set such as sync, anti-sync, triangle wave, square wave, sine wave as well as many other pre-set wave patterns
Create multiple groups
Create and access operational modes such as Feed, Water Change, or Night mode
Monitor power consumption (volts, amps & watts) based on individual pumps & total consumption of all attached pumps
Monitor pump's RPM to ensure maximum performance
EcoTech Vortech pump compatible
Full cloud connectivity so you can control your pumps from anywhere in the world
Real-time notifications of system status & pump performance
Define custom flow patterns of any duration up to 24 hours with 1/1000 second accuracy
Power up to 4 pumps with the Direct Drive ports using a single 100/240V 2.5 amp input power supply (included). The output is 24V/6 amps.
Broad CompatibilityMake pumps from different manufacturers work together to provide a single, integrated flow management system. You can now use a VorTech MP40WQD at one end of your tank and a Reef Octopus Octo Pulse 4 at the other end of the tank and have them work together simultaneously, opposite each other or completely different. Best of all, it isn't limited to two pumps! Add a Maxspect Gyre into the pattern if you want too. Do you have a controllable return pump or skimmerBring them to the party because the HYDROS WaveEngine will control them too! Clutter ReductionThe clutter of power bricks, cables and controllers is becoming an increasing problem for reef keepers. The four pump driver outputs on the HYDROS WaveEngine replace the pump controller, power supplies and any necessary external wireless control modules. Best of all, the HYDROS WaveEngine can run four pumps off a single power supply! Needless to say, it is easy to install. Simply toss out your existing power supplies and controllers, connect the HYDROS WaveEngine and you're ready to start moving water. 0-10V INPUT ControlControl any pump via variable speed INPUT. Unlike other controllers that require intricate programming on pumps connected via 0-10V, the HYDROS WaveEngine allows 0-10V INPUT connected Pumps to take full advantage of all native flow modes and pre-sets without complicated coding.Reverse Pump DriveSome pumps can provide additional pattern options by running in reverse. For example, the Reef Octopus Octo Pulse 4 changes from a highly directed flow to a gentle broad push if you run it in reverse. The HYDROS WaveEngine allows you to take advantage of Reverse Drive to further increase the available flow patterns.Cross Engine SynchronizationMultiple HYDROS WaveEngines can be used to control even larger number of pumps and the patterns will remain perfectly synchronized. A pump connected to HYDROS WaveEngine "A" will run in perfect synchronization with a pump connected to HYDROS WaveEngine "B".Remote AccessA FREE and easy to use iOS and Android compatible app allows you to control everything including flow modes, schedules, pump configuration, as well as monitor performance. You will have no problem with connection because the app can run in cloud mode or local mode. Cloud mode allows you to communicate with your HYDROS WaveEngine when an internet connection is available. The HYDROS WaveEngine system is part of the Amazon Web Services (AWS) and Internet of Things (IoT) platform, guaranteeing high security and reliability. Local control gives you the option of direct access to your control settings in the event your internet connection is unavailable. No matter your situation, the HYDROS WaveEngine will work to keep your tank alive! Real-Time Monitoring and NotificationsYou can set up text message alerts and/or emails to be notified if a pump is blocked or disconnected. If total power failure takes place at your home, bringing down your entire tank and internet connection, you will still be notified via email or text. Do your pumps ever get dirty and drop in performanceThe HYDROS WaveEngine will monitor the power being consumed by each pump along with its shaft RPM and will notify you if the pump's performance is suffering and may require maintenance. Maxspect Gyre 280 pumps can only run at 75% max intensity.PLEASE NOTE: An appropriate pump adapter or 0-10V cable (sold separately) is required to connect pumps directly to the HYDROS WaveEngine.
Hydros Control XS Starter Pack
Hydros XS Controller Starter Kit
Overview
The HYDROS Control XS Starter Kit is the ideal solution for small to midsize aquariums. This controller includes 4 universal-use Sense Ports for aquarium parameter measurement and safety. It's perfect as a standalone controller for a basic saltwater or freshwater tank or combine it with other HYDROS devices as part of a larger system!
What's Included
1x Control XS Unit
1x Power Supply
1x Temperature Sensor
1x 4-Outlet WiFi AC Power Strip
HYDROS App
Set up is quick and easy, making this ideal for both beginner and advanced hobbyists. Monitor temperature, detect leaks, power equipment, control outlets, and more with ease through the HYDROS App. Don't let the compact size of the HYDROS Control XS fool you. It is perfectly capable of performing all the main functions for your saltwater aquarium or freshwater tank. It can monitor temperature, sense leaks, control outlets, send alerts, and much more. All HYDROS products are engineered, assembled, and supported in the USA. The Control XS operates on a HYDROS Safety Net and is rated IP-65 to keep your equipment and aquatic life alive and thriving. All HYDROS products are engineered, assembled, and supported in the USA. is Versatile and Expandable without Extra Modules
Use any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
Features
HYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Sense Port - 4 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Controller Sense Ports currently support
Temperature probes
Optical level sensors (single and dual)
Capacitive non-contact liquid level sensors
Rope leak detectors
Point leak detectors
Flow rate sensors
Magnetic switches
Push-button switches
Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Neptune Apex 1Link Module
Neptune 1LINK Easy, one-click installation!
Overview
The WAV is the first of a line of aquarium products from Neptune Systems that will use a completely new interface. While many in the aquarium world continue to embrace wireless technologies for interconnectivity, we have decided to go the other direction - a wire.
Wireless connectivity from your smartphone or tablet to your Apex (or other controller) is completely logical - and we embrace that. However, wireless used for the interconnecting of devices within the confines of common aquariums (that are mostly less than 6' long) is not only unnecessary, but it reduces reliability.
Our philosophy is that when distances are measured in a few feet, wireless is a solution looking for a problem. And ironically, wireless really does not save wires. You still need to use a wire to get power to the devices anyway. And let's not forget configuration - wireless devices require syncing, endless button presses and arcane steps to get them to connect up - hopefully with you and not your neighbor.
Finally for all this "benefit", you as the consumer get the added cost of this wireless technology that must be baked into the price of every device you buy. So after much study of the problem, our answer is 1LINK.
It is called 1LINK because there is one power supply, one module (for up to three 1LINK devices), and a one-click-connection of a wire that carries not only the power for the device, but two-way communication from it to your Apex. Setup is simply click and go.
Less wires, less configuration headaches, and best of all, less cost to you as a consumer!
Neptune Variable Speed/Dimming Module (VDM)
Overview
The Variable Speed/Dimming module allows for the control of the Aqua Illuminations LED lighting systems as well as adding an additional 4 0-10V variable speed ports.
Features
Independent control of the white and blue Aqua Illumination LEDs.
Simulate Sunrise/Sunset, Lunar Cycle, Clouds, and Lightning with the Aqua Illumination LEDs.
Adds 4 independent 0-10V variable speed ports to the Apex system.
Plug and Play. Automatically recognized when installed into the system.
Two AquaBus connectors for flexible expansion via AquaBus.
Comes with 3' AquaBus cable.
Fully upgradeable.
Led Status indicator.
Compatible with all Apex systems.
The HYDROS Temperature Sensor is an easy and affordable way to prevent your aquarium water from becoming too cold or too hot. It monitors the water temperature in your aquarium so you can keep it within the safe zone for fish, coral, and inverts. The sensor plugs into any Sense Port on a HYDROS device (like the Control 2 or Control 4) and does not require any additional power source.The way it works is easy: just place the sensor inside your aquarium or sump. It can be mounted to surfaces up to 1/2" thick. There is a magnetic coupling that will sit outside your tank or sump to keep the sensor securely in place. You can configure the HYDROS app so that if the water temperature is higher than 82F or lower than 78F (for example), it can send you a mobile alert to let you know. You can also set it up so that outlets that have a heater, chiller, or fan plugged into them turn off when the temperature is outside the safe zone. Your heating and cooling equipment must be plugged into a HYDROS power source, like the Power 4 power strip or Smart Plug, for this sort of automation to occur.The HYDROS Temperature Sensor contains no moving parts that can fail. It's extremely tiny: it's a little over a half-inch thick with a circumference the size of a US penny. The magnet side measures only 1/4" thick. The sensor is easy to place, easy to move, and easy to clean. It provides peace of mind that your aquarium water temperature will never drift outside optimal ranges for aquatic life.The HYDROS Temperature Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Temperature Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor. Keep your aquarium water temperature in the safe zone with the HYDROS Temperature Sensor.HYDROS Temperature Sensor Specs Size: Diameter - 0.75" Sensor - 0.55" thick Magnet Mount - 0.25" thick Max Mounting Thickness: 1/2" No Moving Parts Magnetic Attachment Protects your aquarium from unsafe water temperatures You can use it to shut off a heater, chiller, or fan when the water temperature gets too hot or cold You can set it up so that you'll receive a mobile alert of your water temperature drifts outside the safe zone For freshwater and saltwater aquariums The HYDROS Temperature Sensor uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Manufactured by AutoAqua, an official HYDROS Technology Partner.
Neptune Flow Sensor - 1/2 Inch
Overview
The Neptune Systems FS-50 Flow Sensor is designed to be used with the Flow Monitoring Module (FMM).
Usually used with aquarium accessories like reactors, carbon/GFO filters, etc., this flow sensor can be placed in line with the flow on any pipe, connected to the FMM, and communicate to your Apex the flow rate of water through that pipe.
The flow sensor itself uses BSPP threads so for North American customers we have included two specially designed PVC adapters with slip fittings to adapt it to standard 1/2PVC plumbing.
The FS-50 will work with flow rates from 30-250 gph.
Hydros Control X4/XP8 Pro Pack
Overview
The HYDROS Control X4 PRO Pack includes two Control devices, the Control XP8 and Control X4. Combine these Controls to create a secure and impressive set-up for both saltwater and freshwater aquariums. Connect up to four sensor devices, including temperature sensors, water level sensors, and leak detectors. The device also includes two Drive Ports for powering pumps and solenoids and two Probe Ports for monitoring pH and ORP levels.
Connect up to eight pieces of aquarium equipment, including heaters, lights, pumps, skimmers, and more, to the 120V AC outlets on the Control XP8. Both devices can send alerts and notifications and connect up to 8 WiFi devices for added control on additional equipment. Both devices can send alerts and notifications and connect up to 8 WiFi devices for added modular control on additional equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately). All HYDROS products are engineered, assembled, and supported in the USA.
What's Included
1x Control X4 Unit
1x Control XP8 Unit
1x Temperature Sensor
1x pH Probe & Calibration Solutions
1x 6ft Command Bus Cable with two Terminators
HYDROS App
1 year limited manufacturers warranty
About Control X4
HYDROS Control X4 is a powerful and robust aquarium controller capable of performing all essential functions needed to maintain a healthy aquarium without the need for extra expensive modules. Set up is quick and easy, making this ideal for both beginner and advanced hobbyists. Just one Control X4 can monitor temperature, pH, ORP, and water level, to name a few, and control pumps, timers, level sensors, and much more thanks to its technologically advanced design. It can be used as a standalone controller for saltwater aquariums, freshwater tanks, pond applications, or it can be added to other HYDROS Controls to build a more extensive system. The Control X4 operates on a HYDROS Safety Net and is rated IP65 to keep your equipment and aquatic life alive and thriving. All HYDROS products are engineered, assembled, and supported in the USA.Sense Port - 4 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Control Sense Ports currently supportTemperature probesOptical level sensors (single and dual) Capacitive non-contact liquid level sensorsRope leak detectorsPoint leak detectorsFlow rate sensorsMagnetic switchesPush-button switchesDrive Port - 2 AvailableThe Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported include: Auto Top-Off (ATO) pumpsCooling fansCabinet LED lightsSolenoids to control reverse osmosis systems0-10V PortThe HYDROS Control 4 has 0-10V I/O (input and output) ports that allow it to control and receive commands from other HYDROS devices and accessories from other brands. A legacy automation system can provide input via the 0-10V Ports. They can control variable speed pumps and can also be used to monitor simple switch closures, like push buttons or float switches.Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe. About Hydros Control XP8
The HYDROS Control XP8 is an eight outlet (120V AC) energy bar and controller hybrid specifically designed for equipment like heaters and return pumps which are critical to the life support of any aquarium system. Each of the individually controlled outlets is built into the HYDROS controller for the highest level of security. The Control XP8 has a built-in 60W universal voltage Meanwell power supply with a 14amp max power capacity and is designed to pass ETL/UL certification. Besides the clicking on and off of the controlled outlets, the XP8 is completely passively cooled and with its isolated power circuitry, the controller runs completely silent. Best of all, each of the eight outlets has individual power monitoring capabilities.
FeaturesPower up to 14 amps of system-critical life support equipmentThe Control XP8 is a full brain that can share and take over the decision-making of a HYDROS CollectiveControl up to 8 WiFi devices like fish feeders, smart outlets, and even additional WiFi power stripsCommand Bus port provides power add redundancy power to your HYDROS CollectiveDesigned to pass ETL/UL CertificationUniversal voltage works with both 110 and 220VBuilt- n 60W Meanwell Power SupplyNo noisy fans, the XP8 is completely passively cooledOptical isolation between the power circuitry and the control circuitry. This provides safety failure, and it isolates the control circuitry to reduce noise. Engineered, assembled, and supported in the USA.SpecificationsMax Per Relay: 8ATotal Max Amperage: 14A8 - Controllable Power Outlets - Eight controllable AC power outlets each with individual power monitoring capabilities to safely manage aquarium equipment like heaters, lighting, water pumps, protein skimmers, filters, and pretty much anything else. 2 - Command Bus - The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe. Up to 8 WiFi Devices - Connect up to 8 WiFi devices for added modular control on additional equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately). 1 Year manufacturers limited warranty Versatile and Expandable without Extra Modules
The HYDROS Control X4 and XP8 can be used as a standalone controller for saltwater aquariums, freshwater tanks, pond applications, or they can be added to other HYDROS Controls to build a more extensive system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
What you can expect from your Control X4 and XP8 Control
Check on the health of your aquarium from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor your HYDROS device(s) locally through WiFi
Control X4 and XP8 feature a fast dual-core 32-bit processor
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Monitoring Salinity in an Aquarium can be a ChallengeGet Reliable and Consistent Readings with the SPS KitOne of the biggest challenges with conductivity probes is getting a consistent reading. Many times, the reading is fouled by small bubbles or debris getting on to the probes and end. The SPS Salinity Probe Stability Kit Solves the Problem.The SPS is easy to use! Simply slip the SPS kit over the end of your probe, connect the 1/4in supply line to a small pump such as a Neptune Pmup, or SICCE 90 GPH Micra, or even an open port on your manifold. For the best results, supply the SPS kit between 60 to 100 GPH of consistent and constant flow.The SPS Kit is carefully designed to create just the right amount of water movement and constant pressure around the probe to provide a solid and reliable reading. It will also shielding the probe from bubbles and other debris. If a bubble does get in, the SPS kits constant flow over the probe will act to flush it out and help the reading recover quickly.Basic Installation While supporting the Pressure Screen (B), carefully insert the end of the probe (F) through the top of the SPS Kit Housing (A). Gently push the probe in until it stops against the Pressure Screen. Connect the 1/4in supply line (E) to the push fitting (D) Connect the end of the supply line to the flow source Initial Set-up Place the Probe with the SPS Kit installed into the water and turn on the flow source First - Gently shake the assembly up and down to dislodge any air bubbles that may be trapped inside. Next - Cover the opening at the bottom of the SPS Kit with your finger for a few seconds to expel any reaming air or bubble that may be trapped. The settle in period will generally last a few minutes to as much as an hour. Once settled in, your reading will level out and you should see a steady trend line.
Neptune AquaBus Cable - 6 Foot Male/Male
Overview
6 Foot Male/Male Neptune Apex AquaBus cable.
Used to connect an AquaBus module (PM1, EB8, etc) to another AquaBus Module or Apex base unit.
Hydros Drive Port Extension Cable - 9 Foot
Overview
Extend the reach of HYDROS Drive Port accessories by nine feet for cleaner routing and safer, drier controller placement. This 2-pin extension maintains proper power and signaling for Drive Port devices across stands, cabinets, and sumps.
Features
9 ft extension for HYDROS Drive Port accessories
Preserves stable power/signal delivery for pumps, valves, and Drive-powered add-ons
Durable molded plugs with positive fit to reduce accidental disconnects
Compatible with all HYDROS Drive Port accessories
Specifications
Length: 9 ft
Connectors: HYDROS 2-pin Drive
UPC/EAN: 850009641243
Compatibility: HYDROS Controls with Drive Ports (e.g., Control 2/4 and newer with Drive)
Directions
Power down the controller before connecting
Plug the male end into the Drive Port accessory lead and the female end into the controller/device lead
Route away from salt spray and moving parts; add a drip loop
Power up and verify accessory operation in the HYDROS app
Neptune Leak Detection Kit (LDK)
Overview
Aquarium leaks are one of the most feared events for even the most seasoned aquarist - and for good reason. When it comes to leaks, it's not just about whether you'll have one, but when it happens, will you catch it in timeMost often if you catch a leak in the early stages, when it is a simple drip, you prevent hundreds, if not thousands of dollars in damage.
The LDK includes everything you need to enable your Apex to detect leaks in two locations. Two additional leak detection probes can be purchased separately (4 total).
When the LDK detects a leak, your Apex can sound an alarm, send an alert to your mobile device, or take other actions on your aquarium. The LDK provides the ultimate in disaster prevention for this all too common aquarium issue.
The LDK includes the FMM - Fluid Monitoring Module that is plug-and-play and will work with any Apex. The FMM has four ports for use with the two included leak detection probes. The other two ports are then available to be used for more leak detection probes, flow sensors, or optical water level sensors.
Features
Detects leaks on contact
Instantly alerts you via your mobile device
Monitor for leaks in up to four locations
Includes two leak detection probes (surface type)
Remaining two ports can be used for more leak detection probes or other optional sensors and accessories
Installs in less than 5 minutes!
No programming required!
The slide soaker makes wetting your new Seneye + slide even easier and quicker.It's simple to use just place a new Seneye slide into the soaker and clip it up. Fix the suction cup and stick it the inside of your tank just below the water level.For ponds you can just float it on the surface or in a filter box.There is also an eyelet if you wish to put a leash on it. Having your new slide in the aquarium water will help it wet faster and more accurately.*Seneye+ slide not included
Pinpoint Salinity Monitor
Overview
The PINPOINT Salinity Monitor delivers temperature-compensated salt readings for marine and freshwater systems. Includes 53.0 MS calibration fluid and a conversion chart for specific gravity and % salt. Ideal for reef tanks and koi ponds.
Features
Precise salt concentration measurement
Temperature-compensated probe with 3 ft cord
Conversion chart for SG and % salt
Battery or optional AC adapter operation
Hanna Freshwater Alkalinity Checker
Handheld Checker Alkalinity HI775
Overview
The Hanna Freshwater Alkalinity Checker bridges the gap between simple chemical test kits and professional instrumentation.
Chemical test kits have limited accuracy and resolution since they rely upon the human eye to discern differences in color. Professional instrumentation incorporates a light source such as an LED or tungsten lamp with a filter and a light sensing detector to precisely determine absorbance and ion concentration. Professional instrumentation offers greater resolution and accuracy but can cost hundreds of dollars.
The Hanna Freshwater Alkalinity Checker uses a fixed wavelength LED and silicon photo detector to provide the accuracy of professional instrumentation at the affordable price of a chemical test kit.
Features
Compact and Portable Design.
Built-In Timer
One Button Operation
Easier to use and more accurate than chemical test kits
Dedicated to a single parameter
Ideal for: Water Quality, Environmental, Education, Industrial
Specifications
Range: 0 - 500ppm
Resolution: 1ppm
Accuracy: +/- 5ppm, +/- 5% of reading (based on water temperature of 25c or 77f)
Light Source: LED @ 610nm
Light Detector: Silicon Photocell
Method: Colorimetric Method
Operating Environment: 0-50 degrees Celsius, RH max 95% non-condensing
Battery Type: 1 - 1.5v AA
Auto-Shutoff: Automatically shuts off after 10 minutes of non-use.
Dimensions: 81.5mm x 61mm x 37.5mm (3.2" x 2.4" x 1.5")
Weight: 64 grams (2.25oz)
Warranty: 6 month manufacturer limited warranty
Hydros Salinity Kit
Overview
Keep track of the salinity in your marine aquarium with the CoralVue s HYDROS Salinity Kit. This kit includes the necessary 28ppt and 35ppt calibration solutions to ensure precise conductivity readings.
What's Included
High-range Conductivity Probe
28 ppt Calibration Solution (100 mL)
35 ppt Calibration Solution (100mL)
Specifications
Range: 20 to 2000mS/cm
Operating Temp: 0-80C
Constant: K=10
Housing: POM
Probe Dimensions: 12 x 145mm
Connection: BNC
Cable Length: 3ft
Installing your
Locate the Salinity BNC socket on the conductivity meter/controller and twist clockwise to make the connection. Perform two-point calibration per meter's operation manual to ensure accuracy. For precise conductivity reading use an isolated testing vessel like the HYDROS iV. This add-on ensures that the test sample is physically separated, preventing any electric interference from other equipment in the aquarium system.
Neptune Apex 2 Channel Stream Cable
Overview
The 2 Channel AquaSurf or Apex to stream cable assembly has 1 RJ45 connector which plugs into the Apex base unit, and 2 Din5 connectors which plug into 2 stream pumps allowing operation of the stream pumps through your Apex controller.
Hanna Alkalinity Checker Freshwater Reagents - 25 Pack
HC Checker Reagents Alkalinity HI775-26
Overview
The HI775-26 are the replacement reagents for the HI775 Freshwater Alkalinity Checker HC. These high-quality reagents are manufactured in our state-of-the-art facility and are clearly marked with the lot number and expiration date on each packet for traceability.
The HI775-26 are high- quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Freshwater Alkalinity Checker HC. These reagents follow the Colorimetric Method in which the reaction causes a distinctive range of colors from yellow to green to blue to develop. By simply adding one drop of the Chlorine Remover to remove the chlorine interference, and subsequently adding 1 mL of the Alkalinity Reagent to the sample, the reaction will take place and the HI775 will determine the concentration from the color that is produced. The results will be displayed in ppm of CaCO3 .
These reagents are designed to be used with samples that have an expected range of 0 to 500 ppm CaCO3.
Features
Pre-made reagents for ease of use
Prepared with high purity chemicals
Marked with expiration date and lot number for traceability
Contains 25 Tests for measuring Alkalinity in the freshwater aquarium
Hanna Ammonia Checker Reagent - Freshwaterul> Pre-made reagents for ease of use
Prepared with high-purity chemicals
Marked with expiration date and lot number for traceability
Each package comes with enough reagents for 25 tests
Overview
The Freshwater Ammonia Checker by Hanna reagents are high-quality reagents for use with the HI700 Freshwater Ammonia (ppm) Checker HC.
All reagents are clearly marked with the lot number and expiration date on each bottle for traceability.
Hydros Drive Port Cable
Overview
This HYDROS Drive Port Cable (72 inches long) is designed to connect to an available Drive port on a Kraken, X2, X4, XD, or other HYDROS Control directly to power small 12V devices such as ATO pumps, cabinet LED lights, fans, solenoids, and steering valves.
It features a GX12-2 connector on one end and a standard female 5.5mm x 2.1mm barrel connector on the other. This cable is NOT suitable for 24V applications.
Neptune Flow Sensor - 2 Inch
Overview
Usually used with a return pump, this flow sensor can be placed in line with the flow on any pipe, connected to the FMM, and communicate to your Apex the flow rate of water through that pipe.
The flow sensor itself uses British Standard Parallel Pipe (BSPP) threads so for North American customers we have included two specially designed PVC unions with slip fittings to adapt it to standard 2" PVC plumbing.
The FS-200 will work with flow rates from 300-3000 gph.
Red Sea Iodine Pro Test Kit
Overview
Red Sea's Iodine Pro Reef Test Kit is a unique test, measuring the level of total iodine in your reef aquarium to a high accuracy of 0.01 ppm. Iodine Pro Test Kit enables the accurate dosing of Red Sea's IODINE + TRACE COLORS A Supplement (iodine + other halogens) which is part of the complete Red Sea Reef Care Program.
Specifications
Accuracy: 0.01ppmRange: 0 - 0.09ppmNumber of Tests: 50
Hydros Control Power Supply
Overview
Official HYDROS low-capacity (1A) power supply for HYDROS Controls. Includes a pre-installed HYDROS Terminator, making it ideal for Collectives that use data-only Command Bus cabling or have no spare Command Bus port for a separate terminator.
Features
Includes integrated HYDROS Terminator for proper bus termination
Designed for HYDROS Controls requiring the standard 1A supply
Ideal when building or expanding HYDROS Collectives with data-only cabling
Not compatible with HYDROS WaveEngine or IceCap Dual Pump Controller
Specifications
Output class: 1 Amp (standard HYDROS Control supply)
Compatibility: HYDROS Control XS, X2, X3, X4, Minnow (see notes)
Includes: Pre-installed HYDROS Terminator
Not for: HYDROS WaveEngine (V1/V2/LE) or IceCap Dual Pump Controller
Directions
With power off, connect the supply to the Control’s power input
If used in a Collective, ensure remaining open Command Bus ports are terminated
Use a drip loop and mount the supply in a dry, ventilated area
Restore power and verify normal operation in the HYDROS app
The HYDROS Digital Inline TDS Meter has two sensors to monitor the water quality of any RO/DI system. The corrosion-resistant titanium sensors will provide years of trouble-free readouts.This device plugs directly into any available HYDROS Control Sense Port and does not require any additional power source.Features Simple Installation (includes 1/4in push connect fittings) Two High-Quality Titanium Sensors Small & Compact Design Easy Magnet Mount Display Specifications Range: 0-999ppm Resolution: 1ppm Accuracy: +/- 2% Sensor Cable Length: 24in Display Cable Length: 13ft Size: 2 x 0.6in (diameter x thickness) Please note this requires a HYDROS Control with an available Sense Port to operate - sold separately
Hanna Replacement Test Reagent Vial - 4 Pack
Overview
Replacement Test Reagent Vials for Hanna Water Checkers. 4 Pack Test Vials with replacement stoppers included.
The HYDROS Slim Temperature Sensor Probe is only 1.6" long and 0.32" wide. It's all-black solid waterproof IP68 construction is built for years of reliable service. It is a "set it and forget it" temperature monitor that requires no calibration or maintenance (except for perhaps the occasional cleaning). The HYDROS Slim Temperature Sensor Probe is included with the Control 2 or Control 4, so if you need a replacement or just want to add another temperature sensor to your system, you can easily do so for a very low price.The Slim Temperature Sensor Probe has a long 79" cord with a GX12 aviation-style connector that plugs into any Sense Port on the Control 2, Control 4, and future HYDROS devices. You can use multiple temperature sensors on your system for safety and redundancy. For example, you can place one in your display aquarium and another in your sump. This can be helpful if your sump is in your basement while the display tank is on another floor of the house. The Slim Temperature Sensor Probe is completely submersible so you can easily place it somewhere discreet, like in the back of an all-in-one aquarium, in the overflow, or tucked away in one of the chambers of your sump.The HYDROS Slim Temperature Sensor Probe is an easy and affordable way to prevent your aquarium water from becoming too cold or too hot. It monitors the water temperature in your aquarium so you can keep it within the safe zone for fish, coral, and inverts. The probe plugs into any Sense Port on a HYDROS device and does not require any additional power source.You can configure the HYDROS app so that if the water temperature is higher than 82F or lower than 78F (for example), it can send you a mobile alert to let you know. You can also set it up so that outlets that have a heater, chiller, or fan plugged into them turn off when the temperature is outside the safe zone. Your heating and cooling equipment must be plugged into a HYDROS power source, like the Power 4 power strip or Smart Plug, for this sort of automation to occur. The probe contains no moving parts that can fail. It provides peace of mind that your aquarium water temperature will never drift outside optimal ranges for aquatic life. Keep your aquarium water temperature in the safe zone with the HYDROS Slim Temperature Sensor Probe.Features No moving parts Protects your aquarium from unsafe water temperatures You can use it to shut off a heater, chiller, or fan when the water temperature gets too hot or cold You can set it up so that you'll receive a mobile alert of your water temperature drifts outside the safe zone For freshwater and saltwater aquariums You can run multiple temperature sensor probes for safety/redundancy The HYDROS Slim Temperature Sensor Probes uses a GX12 aviation-style connector so the Control 2 and Control 4 maintain their IP65-rating (dust-tight and protected from water spray at any angle). Powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control 2 or Control 4. No additional power cord is required. Official CoralVue HYDROS Accessory
Hanna Free Chlorine Checker Reagents - 100 Pack
Reliable Chlorine Testing Hanna Meters
Overview
The Hanna HI-93701-01 reagent set includes pre-measured packets for performing 100 free chlorine tests using compatible Hanna photometers. Designed for quick and accurate results, these reagents ensure repeatable measurements critical for water quality monitoring. Ideal for laboratories, pools, and wastewater applications, this set maintains consistency while simplifying your testing workflow.
Specifications
Tests: 100
Parameter: Free chlorine
Method: Adaptation of EPA Method 330.5
Compatible Devices: Select Hanna photometers
EAN: 5060551553306
Shipping Weight: ~0.2 lb (approx. 90 g)
Hydros 2ml/min Dosing Pump
Overview
The HYDROS 2mL/min Dosing Pump is a simple and affordable pump for automating the addition of liquid supplements, trace elements, and two-part solutions to an aquarium.
Connect the power of the dosing pump to any simple timer or aquarium controller (Control XP8 or HYDROS WiFi Power Strip) to completely automate the dosing process. Each pump is capable of dosing a single solution.
A 120V timer or controller is required for automatic on/off operation, sold separately.
Features
Quiet operation
Will not back siphon
4 Rotors
>2,000 hours pump life
Accuracy of +/- 2%
Easy to use with a digital timer
Comes with a dosing pump and a 10mL plastic beaker
Specifications
Average Output: 2mL/min
Fluid Volume: >1.4mL/min
Accuracy: +/-2%
Power: AC 110V /10w
NOTE: The Hydros 2ml/min Dosing Pump does NOT require a Hydros Control to operate!
Hydros Float Switch
Overview
The HYDROS Magnetic Float Switch Sensor is a simple yet effective water level sensor that can be added to any HYDROS Control with an available Sense Port. This Float Sensor can trigger actions such as Automatic Top Off, Turn Off Skimmer, Alarms for Water Level, RO Reservoir level, and anywhere you want to have an input for water level. It features a magnetic mount for easy installation.
Features
Sense Port Accessory
Use as High or Low Level
Magnetic Attachment
For freshwater and saltwater aquariums
The HYDROS Float Switch uses a GX12 aviation-style connector to maintain its IP65 rating (dust-tight and protected from water spray at any angle).
It is powered, monitored, and controlled by plugging into a Sense Port on the HYDROS Control.
Specifications
Cord Length is 6' 6"
Float Switch is 3" long and 3/4" in diameter
Magnet Mount is 1" in diameter, and each side of the magnet is 3/8" (10mm) thick
Max Mounting Thickness: ~2cm
Hydros Control X10
Overview
The Control X10 offers a range of new advanced features, including multi-dosing heads and a salinity probe port, taking aquarium control to a whole new level. This highly versatile controller can effortlessly handle essential functions required for maintaining a healthy aquarium.
With just one Control X10, you can dose liquids, monitor temperature, and track pH or ORP levels. Additionally, you can expand its functionalities by using additional accessories to test salinity and alkalinity, monitor water levels, detect leaks, and power other Control devices.
Whether you have a saltwater aquarium, freshwater tank, or pond, the Control X10 can be a standalone controller or seamlessly integrated into other HYDROS Controls to create a more comprehensive system.
Operating on a HYDROS Safety Net and boasting an IP65 rating, this controller ensures that your equipment and aquatic life thrive in a safe and secure environment. Moreover, all HYDROS products are meticulously engineered, assembled, and supported in the USA
What's Included
X10 Controller
Power Supply p
H Probe with Calibration Solutions
Temperature Sensor
Four (4) 10ft Dosing Tubing
Calibration Beaker
Sense Ports 4 Available
The Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Control Sense Ports currently support
Temperature probesOptical level sensors (single and dual) Capacitive non-contact liquid level sensorsRope leak detectorsPoint leak detectorsFlow rate sensorsTotal Dissolved SolidsDrive Port 2 Available
The Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported include: Auto Top-Off (ATO) pumpsDosing pumpsCooling fansCabinet LED lightsSolenoids to control reverse osmosis systemsSteering valves and relays stirrersHydros IVSalinity Probe Port 1 Available
The Salinity Probe is a special probe port for use with conductivity probes to monitor the salinity of your aquarium's water. Salinity Probe Kit is not included but is required to monitor Salinity.
Command Bus 2 Available
The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
pH/ORP Probe Port 1 Available
One of the most remarkable ports on the HYDROS Control X10 is the Probe Port. You can connect an ORP or a pH probe to the Probe Port but, this is no ordinary pH input! The circuitry is based on an ultra-high-quality input chip specifically designed for these types of probes. Each pH input provides digital galvanic isolation from the rest of the system. Galvanic isolation prevents interference with other accessories connected to the system like motors and pumps. Digital Galvanic isolation preserves the accuracy of the measurement by converting the signal to a digital domain before crossing the isolation threshold.
pH/ORP Probe Ports Currently Support pH MeasurementORP MeasurementAlkalinity input from an external measurement systemHigh Precision Stepper Dosers 4 Available
4 independent fluid metering stepper pumps provide remarkable precision dosing your favorite two part, trace elements, water changes, liquid food additives, and alkalinity testing to name a few common uses.
FeaturesQuiet OperationExact Metering of LiquidsColor-Coded Dosing Heads and TubingEasy to Service What you can expect from your Control X10
Check on the health of your aquarium from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
User sets the alerts and notifications
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Control up to 8 WiFi devices with optional power strips
The HYDROS Leak Detection Sensor is a solid surface leak detector that can sense when freshwater or saltwater is underneath it and use that information to protect your aquarium, home, or office from total disaster.The way it works is simple: plug the sensor into any Sense Port on a HYDROS OS device (like the Control 2 or Control 4). It does not require any additional power source. Next, place the leak detector in a place that makes sense: next to your sump, under your stand, on the lid of a protein skimmer, under your RO/DI system or saltwater mixing station, next to a freshwater ATO reservoir, underneath your carpet, or wherever else there is a potential for leaks. Finally, configure the HYDROS app to perform whatever action(s) you want to happen when a leak is detected: flash a specific light color on your HYDROS controller, turn off a pump, shut down your protein skimmer, send you a mobile alert so you can come home or ask a friend to check on the tank. It's easy to do and you're in control.One common complaint about aquarium leak detectors currently on the market is that they rust on the bottom. Not the HYDROS Leak Detection Sensor. It is completely encapsulated with a safety seal that makes the unit impregnable. This isn't a product you're going to need to replace. It's built to stand the test of time. You can connect as many Leak Detection Sensors as you have Sense Ports available. Using WiFi Power 4 power strips and Smart Plugs, you can power off equipment in another room if a leak is detected. You could have a specific light turn on in your living room or bedroom if a leak is detected. With HYDROS, you could can all sorts of clever stuff to make sure you're in the know should the worst happen!The HYDROS Leak Detection Sensor is an Official HYDROS Accessory manufactured by AutoAqua in Taiwan. Creators of the Smart ATO Micro, AutoAqua is one of the most well-known and trusted makers of aquarium automation systems in the hobby today. CoralVue has thoroughly tested the Leak Detection Sensor to ensure seamless compatibility with the HYDROS platform. The product development team at CoralVue engineered the sensor so it connects with any HYDROS Sense Port using its aviation-style plug for safe operation. No additional power source is needed to run the sensor. Get alerted remotely should disaster strike and take correction action with HYDROS!
Extend to your HYDROS Rope Leak Sense Port Accessory for those larger areas you want to protect.The HYDROS Rope Leak Detection Sensor is a flexible line that detects the presence of moisture anywhere along the rope. Can sense when freshwater or saltwater is underneath it and use that information to protect your aquarium, home, or office from total disaster.Does NOT include an adapter to connect to the HYDROS Control.
Hydros Control X2
Overview
The HYDROS Control 2 is a small, general-purpose aquarium controller capable of managing and controlling all the main functions of an aquarium.
Set up is quick and easy, making this ideal for both beginner and advanced hobbyists. Monitor temperature, detect leaks, power equipment, control outlets, and more with ease through the HYDROS App.
The Control 2 can be used as a standalone controller for saltwater aquariums, or freshwater planted tanks, or it can be added to other HYDROS Controls to build a more extensive system.
The Control 2 operates on a HYDROS Safety Net and is rated IP-65 to keep your equipment and aquatic life alive and thriving. All HYDROS products are engineered, assembled, and supported in the USA.
Hydros Control XS is Versatile and Expandable without Extra Modules
Use any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
Features
HYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Sense Port - 2 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Controller Sense Ports currently support
Temperature probes
Optical level sensors (single and dual)
Capacitive non-contact liquid level sensors
Rope leak detectors
Point leak detectors
Flow rate sensors
Magnetic switches
Push-button switches
Drive Port - 2 AvailableThe Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported by Drive Ports include
Auto Top-Off (ATO) pumps
Cooling fans
Cabinet LED lights
Solenoids to control reverse osmosis systems
Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe. Please note that this is ONLY for the Control 2. Nothing else is included!
Hanna pH Electrode Storage Solution HI-70300L - 500ml
Protect and Maintain Electrode Accuracy
Overview
Hanna Instruments HI-70300L is a premium storage solution designed specifically for pH and ORP electrodes. Proper storage prevents dehydration of the sensitive glass membrane and junction, ensuring accurate and responsive measurements. This 500 mL bottle is ideal for lab and field use, offering a long-lasting supply in an easy-pour design. Whether you're calibrating regularly or storing your electrodes for future use, HI-70300L keeps your probes in optimal condition.
Specifications
Volume: 500 mL
Application: Storage of pH and ORP electrodes
Package: Sealed, tamper-proof bottle
EAN: 8718546851629
Shipping Weight: ~1.1 lb (500 g)
Hydros Launch
Overview
The Launch is the perfect starting point for aquarium control. It measures pH and temperature, controls four outlets, and connects to eight Wi-Fi devices. With additional accessories, it can detect leaks, monitor water levels, track salinity, and more.
About Aquarium Controller
The HYDROS Launch is a multifaceted aquatic support system that combines various features into a single controller. It's an all-in-one solution that allows you to manage a wide range of aquarium functions easily. The HYDROS Launch includes a pH or ORP port, a salinity probe port (salinity probe sold separately), four universal sense ports, four 12V drive ports, 0-10V input control, and four controllable AC Outlets built directly into the controller. It's a great starting point for anyone entering the HYDROS platform. With the HYDROS Launch, you can easily monitor temperature, receive leak notifications, track pH or ORP levels, and power up to four system-critical support devices. You can also expand its capabilities by adding accessories to test salinity and alkalinity, monitor water levels, detect leaks, and power other control devices. Whether you have a saltwater aquarium, freshwater tank, or pond, the Launch can be used as a standalone controller or integrated with other HYDROS Controllers to create a more comprehensive system.
is Versatile and Expandable without Extra Modules
Use any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Drive Port - 4 AvailableThe Drive Ports provide switched 12V DC power for running small lights, motors, pumps, fans, and other accessories. The exact current being supplied by each port is continuously monitored by the Control, so if a motor or pump quits drawing current or draws too much, you will be immediately notified.
Accessories currently supported include:
Auto Top-Off (ATO) pumps
Cooling fans
Cabinet LED lights
Solenoids to control reverse osmosis systems
Hydros IV
Steering valves and relays
0-10V PortThe HYDROS Control 4 has 0-10V I/O (input and output) ports that allow it to control and receive commands from other HYDROS devices and accessories from other brands. A legacy automation system can provide input via the 0-10V Ports. They can control variable speed pumps and can also be used to monitor simple switch closures, like push buttons or float switches.Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe. Sense Port - 4 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.Hydros Controller Sense Ports currently supportTemperature probesOptical level sensors (single and dual) Capacitive non-contact liquid level sensorsRope leak detectorsPoint leak detectorsFlow rate sensorsMagnetic switchesPush-button switchesSalinity Probe Port - 1 AvailableThe Salinity Probe is a special probe port for use with conductivity probes to monitor the salinity of your aquarium's water. Salinity Probe Kit is not included but is required to monitor Salinity.Isolated Testing VesselThis add-on ensures that the test sample is physically separated, preventing any electric interference from other equipment in the aquarium system. HYDROS iV is not included but recommended. switches.pH/ORP Probe Port - 1 Available One of the most remarkable ports on the HYDROS Launch is the Probe Port. You can connect an ORP or a pH probe to the Probe Port but, this is no ordinary pH input! The circuitry is based on an ultra-high-quality input chip specifically designed for these types of probes. Each pH input provides digital galvanic isolation from the rest of the system. Galvanic isolation prevents interference with other accessories connected to the system like motors and pumps. Digital Galvanic isolation preserves the accuracy of the measurement by converting the signal to a digital domain before crossing the isolation threshold. Controllable AC Power Outlets - 4 AvailableFour controllable AC power outlets to safely control aquarium equipment like heaters, lighting, water pumps, protein skimmers, filters, and pretty much anything else.
FeaturesPower up to 14 amps of system-critical life support equipmentThe Control Launch is a full brain that can share and take over the decision-making of a HYDROS CollectiveControl up to 8 WiFi devices like fish feeders, smart outlets, and even additional WiFi power stripsCommand Bus port provides power add redundancy power to your HYDROS CollectiveDesigned to pass ETL/UL CertificationUniversal voltage works with both 110 and 220VBuilt- n 60W Meanwell Power SupplyNo noisy fans, the Launch is completely passively cooledOptical isolation between the power circuitry and the control circuitry. This provides safety failure, and it isolates the control circuitry to reduce noise. Engineered, assembled, and supported in the USA.Specifications
Max Per Relay: 8A
Total Max Amperage: 14A
8 - Controllable Power Outlets - Eight controllable AC power outlets each with individual power monitoring capabilities to safely manage aquarium equipment like heaters, lighting, water pumps, protein skimmers, filters, and pretty much anything else.
2 - Command Bus - The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Up to 8 WiFi Devices - Connect up to 8 WiFi devices for added modular control on additional equipment like lights, pumps, feeders, and more by simply adding a HYDROS WiFi Power Strip or HYDROS Smart Plug (both sold separately).
1 Year manufacturers limited warranty
Versatile and Expandable without Extra Modules
The HYDROS Launch can be used as a standalone controller for saltwater aquariums, freshwater tanks, pond applications, or it can be added to other HYDROS Controls to build a more extensive system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.
Hanna Phosphate Checker - High Range
Handheld High Range Checker Phosphate HI717
Overview
The Hanna Phosphate High-Range Checker bridges the gap between simple chemical test kits and professional instrumentation. Chemical test kits have limited accuracy and resolution since they rely upon the human eye to discern differences in color.
Professional instrumentation incorporates a light source such as an LED or tungsten lamp with a filter and a light sensing detector to precisely determine ion concentration. Professional instrumentation offers greater resolution and accuracy but can cost hundreds of dollars.
The Hanna Phosphate High Range Checker uses a fixed wavelength LED and silicon photo detector to provide the accuracy of professional instrumentation at the affordable price of a chemical test kit.
Features
Compact and Portable Design.
Built-in Timer
One Button Operation
Easier to use and more accurate than chemical test kits
Dedicated to a single parameter
Ideal for: Water Quality, Environmental, Education, Industrial
Specifications
Range: 0-30ppm
Resolution: 0.1ppm
Accuracy: +/- 1ppm, +/- 5% of reading (based on water temperature of 25c or 77f)
Light Source: LED @ 525nm
Light Detector: Silicon Photocell
Method: Adaptation of the Standard Methods for the Examination of Water and Wastewater, 20th edition, Ascorbic-Acid method
Operating Environment: 0-50 degrees Celsius, RH max 95% non- condensing
Battery Type: 1 - 1.5v AA
Auto-Shutoff: Automatically shuts off after 10 minutes of non-use.
Dimensions: 81.5mm x 61mm x 37.5mm (3.2" x 2.4" x 1.5")
Weight: 64 grams (2.25oz)
Warranty: 6 month manufacturer limited warranty
Hydros iV Isolated Testing Vessel iV is an HYDROS Drive Port add-on accessory for the Control X10 to Isolates pH, ORP, conductivity/salinity readouts, and facilitates automatic alkalinity testing.For precise pH and Conductivity readings, utilize the HYDROS iV. This add-on ensures that the test sample is physically separated, preventing any electronic interference from other equipment in the aquarium system. This guarantees more reliable data by eliminating any potential issues. Made in the USA utilizing additive manufacturing techniques. Hydros iV Features Isolates pH and Conductivity Readings from the Aquarium for Interference-free Measurement* Automatic Alkalinity Testing* Mixes Test Sample Stable Tabletop Base and Surface Mountable Directly Power by HYDROS Drive Port *Dosing pump(s), controller, pH, and conductivity probes are not included and are sold separately. Hydros iV Specifications Dimensions (LxWxH): 4.5 x 3.5 x 7.5in (not including Probes and tubing) Available Holders: Two Probes and Four Acrylic Tubing Beaker size: 150ml Cord Length: 6ft Includes: Glass Beaker, Mixing Pill, and 500ml of Pre-Mixed kH Testing Reagent
Hydros Control X3 Starter Pack
Overview
The HYDROS Control X3 can connect to two sensor devices including temperature sensors, water level sensors, and leak detectors. The device also includes a Probe Port for monitoring pH or ORP levels, Control X3 can send alerts and notifications and control outlets for lights, pumps, feeders, and more.
What's Included
1x Control X3 Unit1x Power Supply1x Temperature Sensor1x pH Probe & Calibration Solutions1x 4-Outlet WiFi AC Power Strip HYDROS App
Achieve Ultimate Aquarium Control with Control X3
Set up is quick and easy, making this ideal for both beginner and advanced hobbyists. Monitor temperature, detect leaks, power equipment, control outlets, and more with ease through the HYDROS App.Versatile and Expandable without Extra ModulesUse any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.IP-65 Rated -Splash Proof, Dust Proof, and Secure ConnectionHYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Sense Port - 2 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Controller Sense Ports currently support
Temperature probes
Optical level sensors (single and dual)
Capacitive non-contact liquid level sensors
Rope leak detectors
Point leak detectors
Flow rate sensors
Magnetic switches
Push-button switches
Probe Port - 1 AvailableOne of the most remarkable ports on the HYDROS Control X3 is the Probe Port. You can connect an ORP or a pH probe to the Probe Port but, this is no ordinary pH input! The circuitry is based on an ultra-high-quality input chip specifically designed for these types of probes. Each pH input provides digital galvanic isolation from the rest of the system. Galvanic isolation prevents interference with other accessories connected to the system like motors and pumps. Digital Galvanic isolation preserves the accuracy of the measurement by converting the signal to a digital domain before crossing the isolation threshold.
Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Hanna Phosphate Checker High Range Reagents - 25 Pack
HC Checker Reagents Phosphate HI717-25
Overview
The HI717-25 are the replacement reagents for the HI717 Phosphate High-Range Checker HC. These high-quality reagents are manufactured in our state-of-the-art facility and are clearly marked with the lot number and expiration date on each packet and dropper bottle for traceability.
The HI717-25 are high-quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Phosphate High-Range Checker HC. These reagents follow the Amino Acid Method in which the reaction between phosphorus and reagents causes a blue tint in the sample. By simply adding 10 drops of the first reagent to the sample, followed by the packet of the HI717-25 reagent set, the reaction will take place and the HI717 will determine the concentration from the color that is produced. The results will be displayed in ppm (mg/L) of phosphate.
These reagents are designed to be used with samples that have an expected range of 0.0 to 30.0 ppm (mg/L) phosphate.
Features
Pre-made reagents for ease of use
Prepared with high purity chemicals
Marked with expiration date and lot number for traceability
Contains 25 Tests for measuring Phosphate in the aquarium
Hydros Minnow
Overview
The Hydros Minnow is an aquarium controller with two micro-liquid dosing pumps for precise dosing of two-part and trace elements. It can handle essential functions for maintaining a healthy aquarium and connect up to four sense port accessories like temperature sensors, flow meters, TDS monitors, leak detectors, and more.
About Aquarium Controller
The HYDROS Minnow features two independent micro-liquid dosing pumps for precise dosing of your preferred liquid supplements, including two-part and trace elements. This highly versatile controller can effortlessly handle essential functions for maintaining a healthy aquarium. With just one HYDROS Minnow, you can dose two separate liquids and four sense port accessories like temperature sensors, flow, TDS monitoring, leak detection, and more. Whether you have a saltwater aquarium, freshwater tank, or pond, the Minnow can be a standalone controller or seamlessly integrated into other HYDROS Controls to create a more comprehensive system. Operating on a HYDROS Safety Net and boasting an IP65 rating, this controller ensures that your equipment and aquatic life thrive in a safe and secure environment. Moreover, all HYDROS products are meticulously engineered, assembled, and supported in the USA.
Features
HYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Micro-liquid Dosers 2 Available
The HYDROS Minnow features two independent micro-liquid dosing pumps for precise dosing of your preferred liquid supplements, including two-part and trace elements for reef aquariums. The Minnow's pumps have the following set speeds: -55, -45, -25, 25, 40, 55 (ml/min).
Features
Quiet Operation
Rotatable Dosing Heads
Exact Metering of Liquids
Color-Coded Dosing Heads and Tubing
Easy to Service
Command Bus 2 Available
The HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
Sense Port 4 Available
The Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Sense Ports Currently Support
Temperature sensor - Either air or waterFluid level - Optical sensors to measure liquid levelsLeak detection - Monitoring for both point and wide area leak detectionFlow rate - Measures the amount of fluid flowing through a pipeTotal dissolved solids - Dual measurement of the TDS levels from your RODI system Control Up to 8 Wi-Fi Devices
The HYDROS App allows you to create rules and set schedules to control our 4-Outlet WiFi AC Power Strips and Smart Outlets. Quickly turn on or off different pieces of aquarium equipment like pumps, powerheads, lights, heaters, algae scrubbers, UV sterilizers, protein skimmers, and more. *WiFi Power Strip or Control XP8 is required, sold separately
What's Included
Minnow Controller
Power Supply
Two (2) 10ft Color Dosing Tubing
Calibration Beaker
Hydros Flow Sensor - 3/4 Inch
Overview
The HYDROS Flow Sensors are easy-to-install and measure the flow rate of water passing through it using the HYDROS app.
Available in four sizes: 3/4in (40-800gph), 1in (50-1500gph), 1.5in (100-2500gph), 2in (9200-4050gph)
Monitor Water Flow with
The HYDROS Flow Sensors are easy-to-install flow meters that communicate to the HYDROS app the flow rate of water passing through it. It is safe for use in freshwater and saltwater aquarium systems. The HYDROS Flow Sensors can be used for reactor feed lines and return pumps. Using the HYDROS Flow Sensors can give you peace of mind that your vital aquarium equipment is operating correctly. You can also use the data it collects in the HYDROS app to create rules. For example, if the flow rate were above or below a certain threshold, you can have HYDROS turn off a piece of equipment that is plugged into a Control XP8, Power 4 WiFi power strip, or Smart Plug outlet.
Four Sizes are Available
3/4" Flow Sensor: Flow Range of 40- 800GPH
1" Flow Sensor: Flow Range of 50-1500GPH
1.5" Flow Sensor: Flow Range of 100-2500GPH
2" Flow Sensor: Flow Range of 200-4050GPH
All flow sensors come with schedule 80 PVC Unions, and have an 8' wire length to plug into your Hydros Sense Port. While no power supply is needed, a Hydros Control with an available Sense Port is required for operation.
Hydros Control X3 Monitor Pack
Overview
The HYDROS Control X3 can connect to two sensor devices including temperature sensors, water level sensors, and leak detectors. The device also includes a Probe Port for monitoring pH or ORP levels, Control X3 can send alerts and notifications and control outlets for lights, pumps, feeders, and more.
What's Included
1x Control X3 Unit
1x Power Supply
1x Temperature Sensor
1x pH Probe & Calibration Solutions
1x Point Leak Sensor HYDROS App
Achieve Ultimate Aquarium Control with Control X3
Set up is quick and easy, making this ideal for both beginner and advanced hobbyists. Monitor temperature, detect leaks, power equipment, control outlets, and more with ease through the HYDROS App.Versatile and Expandable without Extra ModulesUse any HYDROS device by itself or connect multiple devices as part of a larger automated aquarium system with NO single point of communication failure. Every HYDROS product is a smart device with its own CPU and scheduling capabilities.IP-65 Rated -Splash Proof, Dust Proof, and Secure ConnectionHYDROS devices look like industrial controllers because they are built to function in the harsh environment of a marine aquarium. The IP-65 rated HYDROS enclosure and aircraft-style connectors ensure long term reliability in the face of splashes and corrosive salt spray.
What you can expect from your HYDROS Smart Device
Control your HYDROS device(s) from anywhere in the world using the technologically advanced HYDROS cloud-based app
Ability to monitor and control your HYDROS device(s) locally through WiFi
A fast dual-core 32-bit processor that allows control decisions to be made within each device
Internal health monitoring to report voltages, currents, CPU status, and the internal temperature of each device
HYDROS Command Bus connections to transfer data and power to devices
Sense Port - 2 AvailableThe Sense Port is a new concept in aquarium parameter measurement. HYDROS devices include several Sense Ports. A Sense Port is a generic input port that can accept data from numerous different types of sensors.
Hydros Controller Sense Ports currently support
Temperature probes
Optical level sensors (single and dual)
Capacitive non-contact liquid level sensors
Rope leak detectors
Point leak detectors
Flow rate sensors
Magnetic switches
Push-button switches
Probe Port - 1 AvailableOne of the most remarkable ports on the HYDROS Control X3 is the Probe Port. You can connect an ORP or a pH probe to the Probe Port but, this is no ordinary pH input! The circuitry is based on an ultra-high-quality input chip specifically designed for these types of probes. Each pH input provides digital galvanic isolation from the rest of the system. Galvanic isolation prevents interference with other accessories connected to the system like motors and pumps. Digital Galvanic isolation preserves the accuracy of the measurement by converting the signal to a digital domain before crossing the isolation threshold.
Command Bus - 2 AvailableThe HYDROS Command Bus is used to power the Control as well as communicate with other HYDROS devices for the ultimate fail safe.
AutoAqua Smart Doser 4
Overview
The AutoAqua Smart Doser offers an ultra compact design with intuitive aquaLine App for controlling your Smart Doser from anywhere in the world! Intuitive and intelligent programming allows you to easily set your daily dosing schedule.
The AutoAqua Smart Doser offers a fully automated and easy to set dosing program, which meets even the most demanding applications. Operating through the aquaLine app, the full suite features simplify every dosing routine. Smart Doser has all the great features to make it an awesome dosing device!
Features
STYLE MEETS SUBSTANCE - Exclusive Hang-On-Back Design allows for convenient and flexible installation, especially small and AIO tank. For larger aquariums, the wall-mount bracket works equally well. Unique plug & play design for no complex tools or procedures!
PATENTED EMPTY MONITOR -Patented optical sensor detects when the supplement bottle is empty and sends an instant alarm. Helping to eliminate fluctuations in your dosing regimen.
INCREDIBLY SLIM DESIGN - With industrial-level gear motor, Smart Doser features a stunning design in an incredibly thin (35mm / 1.4") and light-weight body. The compact size allow you to easily install the doser just about anywhere.
IMPRESSIVE STYLISH DESIGN - Combined with the amazing performance of high-tech touch buttons, attractive indicator LEDs, and brilliant 1/4" push-to-connect fittings, Smart Doser takes everything people love to an entirely new level.
INTUITIVE SETTING INTERFACE - With programming through user friendly aquaLine App, you can easily operate your Smart Doser for various functions and receive instant alarm in every emergency scenario.
WIFI & BLUETOOTH DUAL CONNECTIVITY - Features with intelligent dual connectivity, providing super fast installation and ensuring that you stay connected wherever you are.
Features
Easy-set dosing for Automatic Mode & Manual Mode - Accurate dosing without the hassle of program setting. The Automatic Mode allows user create a program of specific dosing volumes and time period, which automatically distributing dosing time evenly to avoid supplement interference. No more complicated setup and calculation! All programs can be set to run everydayGet rid of Time Allotment and Dosing Overlapping2 Operational Modes : Auto and Manual3 Daily Dose Schedule : day time, night time, 24 hoursVolume dosing will be carried over a specified time periodGrouping Allows Multiple Devices to be Controlled Simultaneously - Ingenious and powerful Cloud system allows integrating multi devices into an unite schedule with no any dosing overlap for a high efficient presetting program. Control the devices simultaneously under same groupConnecting up to 8 pumps for various dosing scenario of Smart DoserMulti-Schedule Management by AWS Cloud SystemFeed Mode - Suspending dosing during coral feeding.Calibration - Calibration with time compensation.Power Outage & Restoration - Keeps setting by powerful memory allocation without battery necessary.Intuitive Interface - Smashing user experience by simple interface.Peace of Mind - Receive instant notifications to any problem monitored by aquaLine, ensuring smooth dosing routine.Specifications
Power:- Input : 100-240 VAC 50-60 Hz - Output : 12 VDC / 1 A - Cable Length : 6 feet (180 cm)Slim Gear Peristaltic Pump: - Power : 2 W @ 12 VDC - Suction Head : 20 feet (610 cm) - Max. Flow : 21 ml/min - Accuracy : +/- 2%1/4-inch Flexible Tubing:- Length : 9.8 feet (300 cm) - Size : ID 5/32 inch (4 mm), OD 1/4 inch (6.4 mm)Max. Mounting Thickness via Hanging Bracket: 3/4 inch (19 mm)Dimensions: (L x H x W) : 6.9 inch x 4.7 inch x 1.4 inch (177 mm x 120 mm x 35 mm)What's Included
Smart Doser 4
Universal Power Adapter
Wall-Mount Bracket
Hanging Bracket
Calibration Cylinder
2 x Tube Clip
2 x 1/4" Quick-Connect Elbows
2 x Mounting Screws
4 x 300cm (9.84 feet) Tubing (Blue / Green / Orange / Yellow)
Red Sea Alkalinity Pro Test Kit
Overview
Red Sea's KH\ALKALINITY PRO Reef Test Kit is an advanced titration test, measuring the level of buffers in your reef aquarium to an exceptionally high accuracy of 0.05 meq/l (0.14 dKH).
Red Sea's Alkalinity Pro test kit enables the accurate dosing of Red Sea's Reef Foundation B supplement (buffer) which is part of the complete Red Sea Reef Care Program.
Specifications
Accuracy: 0.05ppmRange: --Number of Tests: 75
🚨 CANADA POST STRIKE🚨 Due to the strike, we are UNABLE to ship Livestock and Frozen food orders by UPS Express because of the increased volume on their system. Once the strike has ended, regular service will be resumed.
