There is nothing worse than coming down in the morning to finding your favorite fish lying dead and crispy on the carpet.Many fish, especially wrasse, have a tendency to jump from the tank when frightened or chased by another fish and so a solution to preventing the loss of such fish should be high on every fish keepers priority list.D-D Jumpguard covers are a very lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.The Jumpguard Aquarium Cover is a kit of parts which allows the aquarist to create a custom frame for their specific aquarium. The rigid corners and extruded aluminum section create a very solid frame which sits neatly inside glass of the aquarium glass, resting on the top lip. Features New Profile Design - The special extruded aluminum profile is now shaped with a lip which sits directly onto the edge of the glass, removing the requirement for any additional clips or brackets. The section is extruded then powder coated in a tough, low sheen, black finish for greater scratch resistance and greater aesthetics. Improved Corner Moldings - The lower section of the corners is specifically designed so that it does not interfere with the silicone bead in the corners of your tank which gives a tight fit to the glass with no gaps. It also makes it easier and neater to cut off the corner if you want to bring wires out at the back of the tank for pumps and heaters. Maximum Light Penetration - For those concerned with loss of light penetration into your reef tanks, we tested light levels with a Apogee MQ-200 meter and got the following results: PAR without cover around 390 - 400 PAR with cover around 380 - 390 - Approximately a 2.5% reduction in light with no shadowing at all. Accessories - A range of accessories are available to handle any type of aquarium with various pieces of equipment. What's Included 4 x Aluminium frame sections 4 x Plastic corners 2 x Plastic handles 1 x Length of rubber spline 1 x Sheet of clear mesh 1 x Spline roller tool 1 x Instruction manual 1 x Brace bar set (currently 180cm x 90cm model only) Notes 120cm x 75cm is approximately 47.25" x 29.5" The maximum size frame that can be made from each kit will be 3.6cm (1.4") longer than stated in each direction. The tank should be measured from inside face of glass to inside face of glass.
Each Jumpguard Multi-cut-out Set provides you with 3 different cut-out options to allow you to modify the frame around any light brackets, cables or pipework etc. What's Included 1 pair of 15mm offset corners 1 pair of 40mm offset corners 1 x 40mm x 120mm lighting bracket or rigid cut-out NoteCutting into the standard square frame, especially on larger frames, will generally reduce the rigidity and we would recommend installing one of one or more cross braces, as required, to retain the structural integrity.
There is nothing worse than coming down in the morning to finding your favorite fish lying dead and crispy on the carpet.Many fish, especially wrasse, have a tendency to jump from the tank when frightened or chased by another fish and so a solution to preventing the loss of such fish should be high on every fish keepers priority list.D-D Jumpguard covers are a very lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.The Jumpguard Aquarium Cover is a kit of parts which allows the aquarist to create a custom frame for their specific aquarium. The rigid corners and extruded aluminum section create a very solid frame which sits neatly inside glass of the aquarium glass, resting on the top lip. Features New Profile Design - The special extruded aluminum profile is now shaped with a lip which sits directly onto the edge of the glass, removing the requirement for any additional clips or brackets. The section is extruded then powder coated in a tough, low sheen, black finish for greater scratch resistance and greater aesthetics. Improved Corner Moldings - The lower section of the corners is specifically designed so that it does not interfere with the silicone bead in the corners of your tank which gives a tight fit to the glass with no gaps. It also makes it easier and neater to cut off the corner if you want to bring wires out at the back of the tank for pumps and heaters. Maximum Light Penetration - For those concerned with loss of light penetration into your reef tanks, we tested light levels with a Apogee MQ-200 meter and got the following results: PAR without cover around 390 - 400 PAR with cover around 380 - 390 - Approximately a 2.5% reduction in light with no shadowing at all. Accessories - A range of accessories are available to handle any type of aquarium with various pieces of equipment. What's Included 4 x Aluminium frame sections 4 x Plastic corners 2 x Plastic handles 1 x Length of rubber spline 1 x Sheet of clear mesh 1 x Spline roller tool 1 x Instruction manual 1 x Brace bar set (currently 180cm x 90cm model only) Notes 75cm x 75cm is approximately 29.5" x 29.5" The maximum size frame that can be made from each kit will be 3.6cm (1.4") longer than stated in each direction. The tank should be measured from inside face of glass to inside face of glass.
The Jumpguard Flexi-cut-out Set provides you with 2 standard corners and 2 reverse corners to allow you to modify the frame around any larger overflow boxes, light brackets, cables or pipework etc, that would not be covered by the Multi-Cut-out Set.What's Included 1 pair of standard corners 1 pair of reverse corners NoteCutting into the standard square frame, especially on larger frames, will generally reduce the rigidity and we would recommend installing one of one or more cross braces, as required, to retain the structural integrity.
There is nothing worse than coming down in the morning to finding your favorite fish lying dead and crispy on the carpet.Many fish, especially wrasse, have a tendency to jump from the tank when frightened or chased by another fish and so a solution to preventing the loss of such fish should be high on every fish keepers priority list.D-D Jumpguard covers are a very lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.The Jumpguard Aquarium Cover is a kit of parts which allows the aquarist to create a custom frame for their specific aquarium. The rigid corners and extruded aluminum section create a very solid frame which sits neatly inside glass of the aquarium glass, resting on the top lip. Features New Profile Design - The special extruded aluminum profile is now shaped with a lip which sits directly onto the edge of the glass, removing the requirement for any additional clips or brackets. The section is extruded then powder coated in a tough, low sheen, black finish for greater scratch resistance and greater aesthetics. Improved Corner Moldings - The lower section of the corners is specifically designed so that it does not interfere with the silicone bead in the corners of your tank which gives a tight fit to the glass with no gaps. It also makes it easier and neater to cut off the corner if you want to bring wires out at the back of the tank for pumps and heaters. Maximum Light Penetration - For those concerned with loss of light penetration into your reef tanks, we tested light levels with a Apogee MQ-200 meter and got the following results: PAR without cover around 390 - 400 PAR with cover around 380 - 390 - Approximately a 2.5% reduction in light with no shadowing at all. Accessories - A range of accessories are available to handle any type of aquarium with various pieces of equipment. What's Included 4 x Aluminium frame sections 4 x Plastic corners 2 x Plastic handles 1 x Length of rubber spline 1 x Sheet of clear mesh 1 x Spline roller tool 1 x Instruction manual 1 x Brace bar set (currently 180cm x 90cm model only) Notes 180cm x 90cm is approximately 71" x 35.5" The maximum size frame that can be made from each kit will be 3.6cm (1.4") longer than stated in each direction. The tank should be measured from inside face of glass to inside face of glass.
Keep your finny friends safe inside your tank with a customizable Red Sea Aquarium Net Cover. With an extra strong aluminum frame, this screen has a sleek, minimalist design yet is super sturdy and will not warp. Customizable components allow the screen to accommodate rim-mounted equipment such as lighting arms, auto-feeders and overflow boxes, creating a perfect fit with virtually any open-top aquarium.The screen also features clear, thin netting which does not block out light. The frame and net can easily be cut and assembled to be placed on the rim of the tank or to be indented within the tank for a more discreet look.Features Suitable for most open-top aquariums Extra strong, customized aluminum profiles 8mm (5/16") thin strand, transparent netting Inside-rim or on-rim mounting options Spline roller Includes components for one customized cut-out for filters Optional components are available to accommodate other rim-mounted equipment What's Included Aluminum frame sections/profiles Internal and external frame corners Spacers and hangers 8mm (5/16") netting, which can be cut to size Spline rubber for attaching the net to the frame Spline roller for inserting the spline
Keep your finny friends safe inside your tank with a customizable Red Sea Aquarium Net Cover. With an extra strong aluminum frame, this screen has a sleek, minimalist design yet is super sturdy and will not warp. Customizable components allow the screen to accommodate rim-mounted equipment such as lighting arms, auto-feeders and overflow boxes, creating a perfect fit with virtually any open-top aquarium.The screen also features clear, thin netting which does not block out light. The frame and net can easily be cut and assembled to be placed on the rim of the tank or to be indented within the tank for a more discreet look.Features Suitable for most open-top aquariums Extra strong, customized aluminum profiles 8mm (5/16") thin strand, transparent netting Inside-rim or on-rim mounting options Spline roller Includes components for one customized cut-out for filters Optional components are available to accommodate other rim-mounted equipment What's Included Aluminum frame sections/profiles Internal and external frame corners Spacers and hangers 8mm (5/16") netting, which can be cut to size Spline rubber for attaching the net to the frame Spline roller for inserting the spline
Use for circumventing equipment mounts such as LEDs 1 - ZigZag 15 Left (F) 1 - ZigZag 15 Right (F) 1 - ZigZag 40 Left (F) 1 - ZigZag 40 Right (F) Manufacturer Part Number: R42085
For larger aquariums or whenever fitting a cut-out set we recommend installation of one or more brace bars to retain the structural integrity of the frame and to stop the outer edges from pulling in together.What's Included 2 x 900mm x 12mm x 8mm brace bars 2 x T piece connectors 6 x connector clips The Brace bar extrusion and 6 clips are already supplied with the TC18990 (180x90cm) kit as standard.
Use the Universal Cut Out Kit for larger cut outs such as filters and feeders. External corner (A) Internal corner (B) Cut out Profile (P3) Manufacturer Part Number: R42086
Keep your finny friends safe inside your tank with a customizable Red Sea Aquarium Net Cover. With an extra strong aluminum frame, this screen has a sleek, minimalist design yet is super sturdy and will not warp. Customizable components allow the screen to accommodate rim-mounted equipment such as lighting arms, auto-feeders and overflow boxes, creating a perfect fit with virtually any open-top aquarium.The screen also features clear, thin netting which does not block out light. The frame and net can easily be cut and assembled to be placed on the rim of the tank or to be indented within the tank for a more discreet look.Features Suitable for most open-top aquariums Extra strong, customized aluminum profiles 8mm (5/16") thin strand, transparent netting Inside-rim or on-rim mounting options Spline roller Includes components for one customized cut-out for filters Optional components are available to accommodate other rim-mounted equipment What's Included Aluminum frame sections/profiles Internal and external frame corners Spacers and hangers 8mm (5/16") netting, which can be cut to size Spline rubber for attaching the net to the frame Spline roller for inserting the spline
