Kamoer ATO One 2 Smart ATO The Kamoer ATO One 2 is an intelligent water replenishment device, is an upgraded version of ATO One.ATO One 2 SE is the standard version with submersible pump, it only needs to install the sensor and submersible pump, which can be used after power on without setting. The sensor is fixed by magnet, which is convenient for installation and adjustment.Equipped with optical level sensor, blue optical level sensor is used to monitor the water level and decide whether to replenish water, red optical level sensor is used to prevent the overflow.ATO One 2 SE has rich status indication, when the refill water overflows or overtime, when the water in the refill container is insufficient, ATO One 2 SE will have indicator light and buzzer alarm. Specifications of the ATO One 2 Smart ATO by Kamoer Sensor: Optical Sensor Pump: DC12v submersible pump Power Adapter Input: 100-240VAC Power Adapter Output: DC12v 1A
Neptune ATK Auto Top-Off Kit - Version 2 The ATK (Automatic Top-off Kit) is a simple, standalone, and complete solution for replacing water lost to evaporation.Version 2 of the ATK offers an improved PMUP as well as improved optical sensors.The new aquarium hobbyist has many challenges, but none is more annoying than the chore of adding water, every day, to make up for that lost to evaporation (a.k.a. topping off/up). This alone usually makes the automatic top-off (ATO) device the first piece of automation equipment purchased.The ironic flip side of this decision is that a faulty ATO device is one of the leading reasons for catastrophic aquarium failure, or even worse, flooding of the house or business.Not all ATO devices are created equal. Sadly, many ATO on the market are made with cheap components, have very little protection against these catastrophes, and are just a nightmare to assemble and install correctly. Neptune ATK (Auto Top Off Kit) Unique Features Apex owners get even more value - If you already have an Apex of ANY kind, setting up the ATK is still super- simple. Just plug in all the components, attach it to your Apex via the AquaBus cable, and then run the set up task inside Apex Fusion. With the ATK connected to an Apex, you get the added benefit of having email/text/iOS alerts if there is an emergency and you can integrate its operation into other functions. IQ-Fill (standalone mode only) - IQ-Fill (standalone mode only) IQ-Fill is an intelligent and learning algorithm that, ongoing, monitors and records how much water your aquarium needs for each fill, and then calculates a maximum time your pump should run. By doing this, it dramatically reduces the chance that your pump would continue to add large volumes of water to the tank before you could realize it and fix the situation. Back-up mechanical float valve - While a float valve mechanism itself is certainly no high-tech solution, it is exactly what you want to have in place should all this high-tech gear decide to fail. The float valve on the ATK will never see any action unless for some reason the electronics continued to add water to the tank despite the optical sensors being submerged and the IQ-Fill algorithm limiting run times. For those small systems (usually small all-in-one aquariums) where the float valve will not fit, you can remove the float valve from the bracket and you still will have two levels of safety backup. PMUP - the most powerful pump provided with any ATO! - The PMUP is a 24V utility pump that is perfect for moving water from your RODI reservoir to the aquarium. This pump has a vertical design that easily drops into most water jugs or ATO reservoirs. The best part about the PMUP is that it has the power to deliver water to your tank even from remotely located water reservoirs. Most other pumps that come with an ATO will barely pump six feet, the PMUP though has the ability to pump over 14' vertically so it can even pump water up from a lower-floor or basement water storage location! Key Features and Benefits of the Neptune Apex ATK Version 2 Plug and play ready. No mounts to assemble. No bare wires to attach. 3 Levels of Safety Protection! Two optical water-level sensors (one for water level and one for emergency back up) IQ-Fill water run-time intelligence - learns how much water you use at each top-off Mechanical float valve prevents water overrun if electronics should ever fail Does NOT rely on ANY fault-prone mechanical float switches, temperature sensors, or capacitive sensors! Works Standalone (NO APEX NECESSARY!) Advanced features are unlocked when connected to an Apex (i.e. remote failure notification via text, email, or iOS alert) Includes PMUP, a powerful 24VDC pump that can push water�vertically up to 14' Audible failure alarm Additional features with optional accessories What's Included with your new Neptune ATK FMM- Fluid Monitoring Module (runs standalone) Pre-assembled water level mechanism with: Magnetic acrylic mount (works up to 1/4" glass/acrylic) Two (2) optical water level sensors Float valve 90 degree tubing fitting PMUP ATO Pump 24V 36W power supply 4m of orange RO tubing 3/8" -> 1/4" push-fit adapter fitting 1/4" -> 1/4" push-fit siphon break Set-screw for non-float-valve applications
XP Aqua Duetto2 ATO System With huge features jammed in a tiny package, the Duetto is the perfect ATO for your aquarium. XPAqua's proprietary dual-optical sensor packs two precise level sensors in one incredibly small package. In addition to keeping your water level constant, the two sensors also work in concert with the intelligent QST programming to help prevent overfilling.All the installation parts are included and a magnetic coupling allows you to easily mount or adjust the dual-sensor. Installation takes just seconds so you can spend less time working on your aquarium and spend more time enjoying your aquarium. XP Aqua Duetto2 Features New - Controller programming & circuitry for added system protection New - Improved sensor design for longer durability World's smallest dual-sensor ATO Two layers overfill protection Intelligent QST programming Secondary optical sensor Super precise water level control Super easy installation; plug-and-play No programming or adjustments required Works in complete darkness Specifications of the Duetto2 ATO Power Input: 100~240VAC 50-60HZ DC Pump: Head: 8.2ft (250cm) Flow Rate: 74 gph (280lph) Max mounting thickness: 1/2" (12.7mm)
XP Aqua Sumpless ATO2 The XPAqua Sumpless ATO2 is the first and only ATOdesigned specifically for aquariums without sumps. The combination of the sleek overflow box and the innovative dual-optical sensor ATO will help to keep your aquarium topped off and your water crystal clear.The overflow box easily mounts to any aquarium with its magnetic mount. It acts as a surface skimmer to rid your aquarium of undesirable oily surface skim and doubles as a media reactor for carbon, GFO or any media of your choice.XPAqua's proprietary dual-optical sensor packs two precise level sensors in one incredibly small package. In addition to keeping your water level constant, the two sensors also work in concert with the intelligent QST programming to help prevent overfilling.With so many features never seen before in ATO's, the XPAqua Sumpless ATO2 is the ultimate ATO solution for aquariums without sumps. XP Aqua Sumpless ATO 2 Features NEW! - Controller programming & circuitry for added system protection NEW! - Improved sensor design for longer durability Engineered Specifically for Aquariums without Sumps Dual-Optical Sensor for Precise Operation with Secondary Failsafe Intelligent Pre-Programmed Algorithm Doubles as an Effective Surface Skimmer Convenient Media Chamber for Filtration Media Plug-and-Play with All Parts Included Works in Complete Darkness Specifications of the Sumpless ATO 2 from XP Aqua Power Input: 100-240VAC 50-60HZ Flexi Reversible DC Pump: Head: 6.5ft (200 cm) Flow rate: 74 gph (280 lph) ATO DC Pump: Head: 8.2ft (250 cm) Flow rate: 74 gph (280 lph) Flexi Overflow Box: 3.94" x2.17" x6.30" (100mm x55mm x160mm) Max Volume of Media Chamber: 3.74" x1.99" x1.97" (95mm x50.5mm x50mm) 1-der Stick Ultra Media : 3.54" x1.5" x1.89" (90mm x38mm x48mm) Max Mounting Thickness : ½" (12.7mm)
Neptune Liquid Level Sensor - 15 Inch The Neptune LLS Sensors for your Apex controller allow for the measurement of water depth in inches or centimeters.The Liquid Level Sensor is available in four different sizes- 4", 15" 23" and 35" with each sensor having a special place in helping understand the water level in the sump, aquarium, reservoirs, and other liquid-holding containers.No longer do you need to physically look to see how much water level is above or below a specific point, but now simply open the Apex Fusion App and observe. How the LLS from Neptune works The LLS sensor can connect to any available FMM port in your Apex System. Liquid will enter the plastic envelope around the thin material of the sensor. Once the liquid is in contact with the sensor material the LLS uses a patented resistive sensing technology to accurately and reliably measure the liquid level in a container.Included with each LLS sensor is a clip that allows for the mounting of the sensor to the side of the sump, aquarium or container. You can also mount the LLS sensor to a baffle inside the sump. Once calibrated the LLS is accurate to about two-tenths of an inch. Liquid Level Sensor- 15" Applications This is the ideal sensor for your average containers used in and around aquarium. This will be the ideal sensor for measuring the return pump section of your sump. You will be able to make sure that the water level stays consistent and any drops or gains in water level can be carefully examined to make sure there are no changes to your salinity.Further, if, for example, the ATO reservoir is empty and the water level in the return pump area starts to fall, then if using a COR or Vectra pump (new/upcoming feature) you can turn the speed of the return pump down to prevent cavitation.Another great application of the 15" sensor is to place in your ATO reservoir. Especially if you have a reservoir you need to fill manually, often times you simply look at the reservoir while going out the door and know if it is enough water to cover the evaporation rate while you'll be gone. If not, you usually stop what you are doing and take care of it. Now, simply pull out your Apex Fusion App and know without even looking! Application Notes for the LSS The components in the head of the LLS are fully encapsulated in epoxy, but the LLS is not intended to be fully submerged. Care should be taken when selecting the proper length of LLS and installing it to ensure that the water level never exceeds the uppermost graduation mark.
Tunze Osmolator 3 - 3154 Straightforward and safe water level controller for fresh and sea water with optical control sensor and independent thermal safety sensor. A constant water level keeps the salt concentration constant in seawater aquariums. Incl. Turbelle High Jet 5030 dosing pump with integrated dry running and blockage protection, magnet holder, 12V DC power supply unit, tube and tube holder. Suitable for placement in cabinet filter systems or on the edge of the aquarium. The sensor holds on glass panes up to 15 mm (0.59") and the tube holder up to 22 mm (0.87"). Features of the Tuzne Osomolator 3154 Large, Precise Optical Sensor - Detects the water level with an accuracy of 0.5 mm, resists air bubbles, deposits and scratches. The independent thermal safety sensor stops the Turbelle High Jet 5030 pump in the event of overfilling, ensuring 100% overflow protection. Plug & Play - All required components are ready for installation in the package (except reservoir). No software setup required. The fixed parameters are based on many years of experience. Turbelle High Jet 5030 - Long-lasting high-tech dosing pump Turbelle High Jet 5030 with a maximum delivery height of 6.2 m (20.34') and pleasantly quiet operation thanks to a real 3-phase sine wave. High-Tech Cable - With remarkably high abrasion resistance, seawater resistance and extreme resistance to mechanical impact. As a result, it does not harden in water like PVC cables. With an extra high-contrast intermediate cable sheathing to detect damage at an early stage. Produced in Bavaria by MEDI Kabel. Hose & Hose Connectors Included - The set includes a corrosion-resistant, screw-in push-in fitting (1/4 inch BSP to 6 mm diameter). In addition, a PU hose made entirely in Germany - low-emission, hydrolysis-resistant, microbe-resistant, flexible, but does not tend to kink when laid.
Compact All-In-One Construction - With magnet holder and tube holder for an attachment to any aquarium edge or in the aquarium filter up to 15 mm (2/3").
Kamoer ATO One 2 Smart ATO for RO The Kamoer ATO One 2 is an intelligent water replenishment device, is an upgraded version of ATO One.ATO one 2 RO is the version with a solenoid valve. It only needs to install the sensor and solenoid valve, which can be used after power on without setting. The sensor is fixed by magnet, which is convenient for installation and adjustment.Equipped with optical level sensor, blue optical level sensor is used to monitor the water level and decide whether to replenish water, red optical level sensor is used to prevent the overflow.ATO One 2 RO has rich status indication, when the refill water overflows or overtime, when the water in the refill container is insufficient, ATO One 2 RO will have indicator light and buzzer alarm. Specifications of the Smart One 2 ATO for RO by Kamoer Sensor: Optical Sensor Solenoid Power Adapter Input: 100-240VAC Power Adapter Output: DC12v 1A
Neptune Liquid Level Sensor - 23 Inch The Neptune LLS Sensors for your Apex controller allow for the measurement of water depth in inches or centimeters.The Liquid Level Sensor is available in four different sizes- 4", 15" 23" and 35" with each sensor having a special place in helping understand the water level in the sump, aquarium, reservoirs, and other liquid-holding containers.No longer do you need to physically look to see how much water level is above or below a specific point, but now simply open the Apex Fusion App and observe. How the LLS from Neptune works The LLS sensor can connect to any available FMM port in your Apex System. Liquid will enter the plastic envelope around the thin material of the sensor. Once the liquid is in contact with the sensor material the LLS uses a patented resistive sensing technology to accurately and reliably measure the liquid level in a container.Included with each LLS sensor is a clip that allows for the mounting of the sensor to the side of the sump, aquarium or container. You can also mount the LLS sensor to a baffle inside the sump. Once calibrated the LLS is accurate to about two-tenths of an inch. Liquid Level Sensor- 23" Applications The 23" sensor is a bit larger version of the 15" sensor and can be utilized in similar applications to the 15" but for larger sized-aquariums A great application to consider is utilizing these advancing a roller mat. Application Notes for the LSS The components in the head of the LLS are fully encapsulated in epoxy, but the LLS is not intended to be fully submerged. Care should be taken when selecting the proper length of LLS and installing it to ensure that the water level never exceeds the uppermost graduation mark.
Neptune Liquid Level Sensor - 4 Inch The Neptune LLS Sensors for your Apex controller allow for the measurement of water depth in inches or centimeters.The Liquid Level Sensor is available in four different sizes- 4", 15" 23" and 35" with each sensor having a special place in helping understand the water level in the sump, aquarium, reservoirs, and other liquid-holding containers.No longer do you need to physically look to see how much water level is above or below a specific point, but now simply open the Apex Fusion App and observe. How the LLS from Neptune works The LLS sensor can connect to any available FMM port in your Apex System. Liquid will enter the plastic envelope around the thin material of the sensor. Once the liquid is in contact with the sensor material the LLS uses a patented resistive sensing technology to accurately and reliably measure the liquid level in a container.Included with each LLS sensor is a clip that allows for the mounting of the sensor to the side of the sump, aquarium or container. You can also mount the LLS sensor to a baffle inside the sump. Once calibrated the LLS is accurate to about two-tenths of an inch. Liquid Level Sensor- 4" Applications The 4" LLS is the smallest of the four sensor offerings. It is the perfect fit for small reservoirs for small sumps, ATO reservoirs and additive containers. The smallest LLS can be a great solution to double check that liquid additions of your additives match your dosing solution over a period of time. For example, if you dosed 250 mL additives over two weeks and you know each inch is 100 mL, then the additive reservoir liquid level would have decreased exactly by 2.5". Application Notes for the LSS The components in the head of the LLS are fully encapsulated in epoxy, but the LLS is not intended to be fully submerged. Care should be taken when selecting the proper length of LLS and installing it to ensure that the water level never exceeds the uppermost graduation mark.
TUNZE Osmolator 3 Nano Looking for a reliable and efficient way to maintain a consistent water level in your aquarium? The TUNZE Osmolator 3 Nano is the ultimate auto top-off (ATO) solution designed for small to medium-sized aquariums. Perfect for tanks up to 250 liters (66 US gallons), this device ensures a stable and safe water level, making it an essential tool for both freshwater and saltwater aquarium enthusiasts. Why Choose the TUNZE Osmolator 3 Nano? 1. Precision Optical Sensor The Osmolator 3 Nano features a single, high-precision optical sensor capable of detecting water level changes with an accuracy of 0.5 mm. It's designed to resist air bubbles, deposits, and scratches, ensuring reliable performance over time. 2. Wide Compatibility Works with glass panes up to 12 mm (1/2") thick. Compatible with both cabinet filter systems and direct installation on the aquarium edge. Includes a hose holder for aquarium edges up to 22 mm (0.87"). 3. Powerful Dosing Pump Equipped with the Turbelle High Jet 5030 dosing pump, the system can handle water delivery heights of up to 6.2 meters (20.34 feet). Plus, it operates quietly thanks to its real 3-phase sine wave technology. 4. Built-In Safety Features The Osmolator 3 Nano includes two selectable maximum dosing durations, allowing you to adjust water addition based on your aquarium's size. This feature prevents overfilling and ensures your tank remains safe. 5. Complete Installation Kit The package comes with everything you need: 12V power supply Low-voltage dosing pump 3-meter hose Hose holder Magnet holder (for glass up to 12 mm) Protective cover for the sensor Who Can Benefit from the TUNZE Osmolator 3 Nano? This ATO system is ideal for: Hobbyists maintaining aquariums up to 250 liters Aquarists looking for a reliable and easy-to-install water level management solution Owners of both freshwater and saltwater setups Trusted Brand with a 5-Year Warranty TUNZE is a renowned name in the aquarium industry, known for high-quality products. The Osmolator 3 Nano comes with a 5- year warranty, offering peace of mind and showcasing the brand's commitment to durability. If you're searching for an efficient, safe, and user-friendly auto top-off system, the TUNZE Osmolator 3 Nano is the perfect choice. With its precision sensor, reliable dosing pump, and comprehensive safety features, this device ensures your aquarium's water level stays consistent, supporting a healthy aquatic environment. Get the TUNZE Osmolator 3 Nano today and experience hassle-free aquarium maintenance!
AutoAqua Smart Automatic Water Changer Lite The Smart AWC Lite from AutoAqua is a pioneer in automatic water change which is integrated with a diaphragm pump into controller. Its high efficient diaphragm pump and patented dual-optical sensor let you blitz through the most demanding tasks faster and easier than ever before. No more lugging buckets and jugs! Integrate Design and Ultra-High Performance All in one ATO and AWC, with patented optical dual sensor and high efficiency DC diaphragm pump, you can easily maintain your tank both hands and worry free. Turning off return pump is unnecessary during water change. Intuitive Interface and Smart Operation Designed for simplifying the routine of remove and replenish aquarium water. Features with intuitive interface with LED indicators and 5 pre-time setting, each status can been seen at a glance without technical jargon or complex system. Sense Everything with the Precision Engineered Sensor Upgraded optical sensor designed for more precise detection of water level even at a distance of 1 mm and against false detection due to water drop. Continuation of advantages in patented dual optical sensor, the failsafe sensor will be a backup and protect your tank immediately even the main sensor is failed. Strong but Quiet - Precise But Safe With a built-in timer , the QST provides real-time failsafe protection to prevent any failure situation. It avoids overfilling instantly and the reservoir empty, without any complicated settings. Hobbyists can fully rely and trust the safety of our automatic system and peace of mind. Quick Security Technology and High Level Safety With a built-in timer , the QST provides real-time failsafe protection to prevent any failure situation. It avoids overfilling instantly and the reservoir empty, without any complicated settings. Hobbyists can fully rely and trust the safety of our automatic system and peace of mind. Superior Structure and the Simplest Installation The exclusive & ingenious accessories and plug-and-play design will be an open sesame to tidy clean aquarium and build you aquarium to your needs. An all Inclusive Detail Oriented Automatic Water Changer for Aquariums The exclusive & ingenious accessories and plug-and-play design will be an open sesame to tidy clean aquarium and build you aquarium to your needs. What's Included with the AutoAqua Smart Automatic Water Changer Lite Smart AWC Lite Controller Universal Power ADapter Quad Tube Holder Aqua Lifter Pump Holder Prefilter Prefilter Base Tube Clip 19.6' (6m) Tubing Auto Aqua Smart Automatic Water Changer Duo Specifications Power Power Input: 100-240 VAC 50-60 Hz Power: 4.5 W @ DC 12 V Power Cord Length: 6 ft (180 cm) DC Diaphragm Pump (Built-in Anti-Siphon Valve): Suction Head : 6.5 ft (200 cm) Flow Rate : 3.2 gph (12 lph) Anti-Siphon Pressure : 1 feet (30 cm) of water. The height from water level of reservoir to tube outlet must be smaller than 1 feet (30 cm). Max. Mounting Thickness: Sensor: 1/2 inch (12.7 mm) Quad Tube Holder: 1/2 inch (12.7 mm) AQUA Lifter Pump Holder: 1/2 inch (12.7 mm) Length of Cable between Sensor and Controller: 9.8 ft (300 cm) Tubing: Length: 19.6 feet (600 cm) ID : 5/32 inch (4 mm) / OD : 1/4 inch (6.4 mm)
Kamoer X2SR Auto Water Change Pump Automatically Perform Water Changes!X2SR is a water change system that can remotely control it through the mobile phone App using WiFi. The automatic water replenishment function can be completed through the submersible pump interface.To mitigate possible overflow risks, X2SR comes standard with an anti-overflow sensor. When the water level reaches the anti-overflow sensor, an alarm will be triggered, and the water supply and change will stop. Specifications of the Kamoer X2SR AWC Pump Flow: More than 900ml/min Power Adapter Input: 100VAC -240VAC Output: DC24V 1.9A Number of dosing: 24 times/day-1 time/99 days Interface: WiFi (App remote control) Working environment: Temperatures: 0 - 70C; Humidity: 10% - 90% (non-condensation) Dimensions (L*W*H): 168*177*223mm (including pump head) Weight: 4.106KG (not including power supply) What's in the Box of your new X2SR Pump Package by Kamoer 1 - X2SR Power adapter body (DC24V 1.9A) Power adapter plug (US/UK/EU/AU) Plastic cylinder (50ml) PVC tube 9.5*12.5mm; green 6m Kamoer tube manifold Transparent Float level sensor(headphone plug) Float level sensor bracket Magnet (black) A submersible pump(DC 24V) Male-to-male line 12 PVC connecting pipe for auto top-off 8*11mm transparent 1.5m Anti-siphon connector(1/4 straight) Grease x 10g Quick start guide Qualified certification Percautions when using your X2SR Auto Water Change Set-up from Kamoer Please use the product's own power adapter and work in the specified working environment. This product only supports 2.4G Wi-Fi, not 5G Wi-Fi. Perform flow calibration before using the device to ensure that the water output is the same as the water input when changing water. The connecting pipe for the liquid inlet should be as short as possible, and the connecting pipe for the liquid outlet should be suspended above the tank. Please carefully check whether the connection direction of the water inlet and outlet is correct, and do not connect them in reverse.
Neptune Liquid Level Sensor - 35 Inch The Neptune LLS Sensors for your Apex controller allow for the measurement of water depth in inches or centimeters.The Liquid Level Sensor is available in four different sizes- 4", 15" 23" and 35" with each sensor having a special place in helping understand the water level in the sump, aquarium, reservoirs, and other liquid-holding containers.No longer do you need to physically look to see how much water level is above or below a specific point, but now simply open the Apex Fusion App and observe. How the LLS from Neptune works The LLS sensor can connect to any available FMM port in your Apex System. Liquid will enter the plastic envelope around the thin material of the sensor. Once the liquid is in contact with the sensor material the LLS uses a patented resistive sensing technology to accurately and reliably measure the liquid level in a container.Included with each LLS sensor is a clip that allows for the mounting of the sensor to the side of the sump, aquarium or container. You can also mount the LLS sensor to a baffle inside the sump. Once calibrated the LLS is accurate to about two-tenths of an inch. Liquid Level Sensor- 35" Applications The largest of the LLS sensors is the 35" sensor. This sensor is to be used for large reservoirs that are often utilized for saltwater reservoirs for manual and automatic water changes. Application Notes for the LSS The components in the head of the LLS are fully encapsulated in epoxy, but the LLS is not intended to be fully submerged. Care should be taken when selecting the proper length of LLS and installing it to ensure that the water level never exceeds the uppermost graduation mark.
