Reef Brite K-Series LED Add-On Brackets
Reef Brite® is excited to announce the new K-series LED ADD-ON KIT Brackets for Ecotech Radion® AI Hydra® fixtures with RMS and HMS™ mounts. Also works with new G5 fixtures and mounts. The K-Series LED ADD-ON Brackets allow users to attach a pair of XHO’s (Not included) to Ecotech Radion® AI Hydra® fixtures with RMS and HMS™ mounts to help increase intensity, PAR, color and pop while improving coverage and illuminating dead spots and shadow areas in your tank. Each kit includes two Reef Brite XHO-B30 Brackets.
Important please read all instructions carefully before installing your K-series LED ADD-ON brackets:
Reef Brite has gone through great care to ensure that the K-series LED ADD-ON Brackets install seamlessly to your fixture or lighting system. Due to various tank sizes/glass thicknesses and older style mounts offered, before installing it is very important that you check your tank manufacturers specs as well as checking the mount you are using to ensure that it is compatible and can support the additional weight. Reef Brite will not be responsible for improperly installed kits or any damages that may result.
Installation instructions for RMS and HMS™ mounts:
When working near or around your aquarium make sure all working surfaces are completely dry before handling any electrical equipment.
Make sure your fixture is unplugged from electrical outlet and disconnected from the power supply before attempting to install the K-Series LED ADD-ON Brackets.
If fixture was in use even for just a short period let cool. LED’s can get very hot during operation and can cause personal injury or damage surfaces if proper care in handling is not taken.
Once cool, place fixture on a secure table or work surface.
XR series locate the four M5 x 12mm mounting screws included with your K-Series LED ADD-ON brackets. Hydra HD series locate the two M5 x 25mm screws that came with your K-Series LED ADD-ON brackets. These screws are required to install the K-Series LED ADD-ON Brackets.
Do not attempt to use hardware not supplied with your K-Series LED ADD-ON Brackets as damage to your fixture could result.
Attach the two brackets that came with your K-Series LED ADD-ON Brackets by placing them under the RMS or HMS™ mount you are using for your XR or Hydra HD series light so that the holes align with the RMS or HMS™ mount and the threaded holes on your fixture.
Using the provided hardware attach the brackets and mount to the fixture. It is recommended to use care when threading the screws and avoid overtightening the screws once installed.
Install the two XHO’s (Not included) with the screws originally provided on the ends of your XHO’s.
Make sure to locate the power supplies for your XHO’s (Not included) in a safe location away from any contact with water.
Carefully attach your fixture to the aquarium mount, plug in fixture and power supply to a GFI outlet (Recommended) assuring a proper drip loop is employed.
Important note: Use of power strips located on floors or any location where water can come in direct contact with them is dangerous and can cause serious injury or fire. Make sure all electrical plugs and electrical outlets are safely located so that water cannot splash or spill on them.
Installation instructions for hanging kits:
When working around water make sure all working surfaces are completely dry before handling any electrical equipment.
Make sure your fixture is unplugged from electrical outlet and disconnected from the power supply before attempting to install the K-series LED ADD-ON Brackets.
If fixture was in use even for just a short period let cool. LED’s can get very hot during operation and can cause personal injury or damage surfaces if proper care in handling is not taken.
Attach the two brackets that came with your K-Series LED ADD-ON Brackets by placing them over the top of the fixture, so that the holes in the K-Series LED ADD-ON Brackets align with the threaded holes on your fixture.
HD series the posts that comes with your hanging kit go through the center hole on the bracket to attach brackets to your fixture. The K-Series LED ADD-ON Brackets are designed so that the posts for the hanging kit keep the brackets secured in place.
Using the supplied hardware that came with your hanging kit attach the hanging kit and brackets to your fixture.
Do not attempt to use hardware not supplied with your hanging kit or K-Series LED ADD-ON Brackets as damage to your fixture could result.
Install the two XHO’s (Not included) with the screws originally provided on the ends of the XHO’s.
Make sure to locate the power supply for the XHO’s (Not included) in a safe location away from any contact with water.
Carefully attach your fixture to the hanging cables, plug in fixture and power supply to a GFI outlet (Recommended) assuring a proper drip loop is employed.
Important note: Use of power strips located on floors or any location where water can come in direct contact with them is dangerous and can cause serious injury or fire. Make sure all electrical plugs and electrical outlets are safely located so that water cannot splash or spill on them.
IMPORTANT NOTICE: When installing any lighting product, power supply, or controller do not install in a manner that will allow any part or component to come in direct contact with water. Reef Brite assumes no liability for incorrectly installed products.
